So? Some information about closing the G-tread?

[Robert T]

I checked last night and I got my G-tank Sept. 1st. That night I sat down at the table with my iPad and did the wick and coil with the video, step by step. Worked the first time and I've been using it since. I checked it after a week and it didn't look dirty but I cleaned it anyway. I didn't check it again for a couple of months, seemed to be working fine, then a couple of weeks ago I checked it and it looked a lot like asdaq's so I cleaned it. That's almost 3 months so I would say that's pretty low maint. lol

Robert

i have been running mine since i put it together over a month now , it's 1.5 ohm and havent had to do any cleanings to it, have been diy my own eliguid,some light some med. dark. and still good to go

 

[eyebrook]

I use a lot of coffee and chocolate liquids so give it a dry burn and clean it with a toothbrush and its as good as new

 

[asdaq]

Cheers, good idea. I gotta give dry burns more of a chance here. Only trouble is they taste awful and are a typical indicator to fill up the tank again.

 

[eyebrook]

Ive just done my wick , dry burned it and then used toothbrush and hot water to remove the ash, good as new, back in business

 

[sjmck]

I seem to get about 8 weeks from a mesh & coil using eyebrooks method of cleaning

Last time I thought I would try and replace only the coil, but when I tried to unwind it the mesh started breaking up

Not bad for 8 weeks though, I would have normally spent £15 on dual coils in that time.

 

[chuckie]

Its to use the G Tank on an Ego type battery so it hides the thread on the Ego

That's what I figured,but having never had an ego,I had no way to try it.Thanks for the answer.

 

[asdaq]

After one tank it looked about half as bad as in the pic, so I took the coil off and an entire layer of mesh came off with it, almost a perfect square right under the coil. I'm quite sure the pores were blocked in the mesh behind the coil so liquid would ball up on the outside. Now I've replaced everything and am officially on my second wick. Still a nice track record on the first.

 

[chuckie]

How long have we had these tanks? (I'm too lazy to look it up).I'm thrilled at how trouble free these tanks are.
Thanks again Oosturm.

 

[raceengine]

I got them on sept 5th. close to 3 months already... up for the g-tank

 

[Smacker]

Anyone know how to get updates on sturm's G-mod? Got this today:

According to this forum, another week and it will be shipped.
Prijava
David

Unable to confirm but sounds good!!

These translators drive me nuts................. Is there a good one out there?

 

[UA72Riddle]

Anyone know how to get updates on sturm's G-mod? Got this today:

According to this forum, another week and it will be shipped.
Prijava
David

Unable to confirm but sounds good!!

These translators drive me nuts................. Is there a good one out there?

No good translators for Croatian, but that is where his thread is now....and in english. Check here.....this was the last post.

 

[asdaq]

Smacker, looks like they have shipped. In Poland they arrived about 10 days ago, Peace got his in Croatia on the 30th, so if you are expecting one in MD, it should be very soon. More here, and I'd stick with google translate:

Zobacz temat - STURM MOD • PapierosyForum.pl - wszystko o elektronicznych papierosach



Your link is Croatian I think

 

[Ariel_MX]

So maybe next week my Sturm MOD will start it travel to Mexico

 

[Brazilleon]

It looks fantastic. I can't wait to see my GTank on it.

 

[ainako]

Scored one of these from the classys! I already have a wick pre-seasoned and ready to go once it arrives. BOO YAH! SO EXCITED! this should hold me off good until my g-tank-us and GenLVs arrive. BTW anyone know where I can source the syringe tank here in the states?

 

[raceengine]

local pharmacy? 2.5ml syringe fits nicely

 

[ainako]

I have a bunch of 3mL BD syringes, hopefully they fit ok. I guess I'll find out once it comes, will alert the ECF family of my findings. 2.5mL syringes seem hard to find

 

[otrem]

3ml BD fits fine.

 

[otrem]

the sturm mod w/ the gtank.
from the polish forum.

 

[ainako]

First day with sturm's g-tank, works pretty well besides the occasional dry hit. I found it quite difficult connecting the kanthal to the screw posts but got it up and running ok. Although I have to adjust the center post, out of the 3 precise plus top caps that I have, it only works with one. So I'm guessing I have to adjust the s-wire a bit, only problem is I cannot get the brass part off for the life of me, anyone have any tips as to how to get it off. Also I remember a more robust way to create the center post but for the life of me I can't find where I saw it.