- Status
I would be interested in the 3/4" preferred and the 5/8" if that is what gets made. I would like to get 4 of them if they are made in a 510 kit. I have Kanthal and ss mesh, but I can't find a reasonably priced machinist that has time to make single orders.
I'd be ok w/ a 5/8" OD as well. We can always control the 'ml' it'll hold by length of the tank.
The Redilast2900 and the AW2900 are just re-wrapped Panasonic cells (they just add their own PCB as Panasonic cells are unprotected).
For Li-Ions, AW's own 2600 is a cheaper and better cell for our uses.
Note in this 2A drain test that although the Panasonics would last a tad longer in a flashlight the AW2600 maintains a higher voltage (less voltage sag) during a normal vaping range.
You might also find the AW IMR trace interesting. Although it starts higher than the others the voltage drop is quite extreme and quick.
The 5/8"-3/4" is just a bit on the "fat" side. I wouldn't mind something a bit smaller in OD than your standard 14500 pv.
Length IS important. What it fits in, how prone it is to breaking. Long atty + drip tip means you end up with a LOT of leverage out towards the tip. Not good for excessive angular force towards the connector end.
What you want to weigh it against is capacity. I think 1 ml is the minimum and probably too small. I would find 1.5 ml capacity ideal. The Genisis I have now is about 3 ml.
The downside of 1/2" - 5/8" is the 1/16" wall thickness... I think that's a no go. I'd like to see 1/8" wall thickness at a minimum? A main factor inspiring this was tank replacement... because they break.
AW uses different (mfg) cells for the 2600. I think AW employs physical disconnects in addition to the PCBs. Both quality batteries.
http://www.candlepowerforums.com/vb...-Battery-Unwrapping-(w-trustfire-2400-post-50)
.
Thanks, but I think the cap is not necessary. To replace Kanthal, irrigation chamber for the liquid. I am running without the cap long enough. No maintenance required. The system is cheaper without the cap. Dimension is the ego ideal. Liquid capacity of 2.3 ml. I have a visual inspection of spirals.
I tested a lot of settings, but I did not find any better.
Rockwomen
I like the 1/2" ID 5/8" OD size also . Hey and when do we get a look at the top-secret plans you have spoken of for the build?
Dan
I like the 1/2" ID 5/8" OD size also . Hey and when do we get a look at the top-secret plans you have spoken of for the build?
Dan
I'm looking to stay with 3/4 personally for the tank, but I kinda like that ego battery genesis posted on the previous page too. Very nice 
Although similar there are better choices. Like round ones that are basically a pin and a threaded sleeve. I don't think anyone is at that level of detail yet.
Although similar there are better choices. Like round ones that are basically a pin and a threaded sleeve. I don't think anyone is at that level of detail yet.
oh. I thought that was what Rockwoman meant by top connections.I use something similar but they are the connections out of an electronic thermostat.
Is the battery end being considered for the Co-op? I would consider jumping aboard for a 18650 in the smallest tube possible.
Screw-on top makes the most sense in my opinion.
Considered. Current direction appears to be towards a Genisis atomizer with a 510 connector.
I agree...the smaller the better....these things are incredibly top heavy....and I usually dont get through a full tank without a 'freshen up' top off...dont see the issue with a smaller tank...
A suggestion for the co-op.
If you can spec out all the parts, it would be awesome if you also included the kanthal and mesh (maybe 1 sq ft).
I keep telling myself I'll build a genesis, and probably will, but if I were to buy one, considering all the trial and error required to find out "what I like", the best purchase would be a set that included all the necessary start-up components.
Just my $0.02
If you can spec out all the parts, it would be awesome if you also included the kanthal and mesh (maybe 1 sq ft).
I keep telling myself I'll build a genesis, and probably will, but if I were to buy one, considering all the trial and error required to find out "what I like", the best purchase would be a set that included all the necessary start-up components.
Just my $0.02
I like 3/4" od. and a length that will allow for about 3mls. of liquid.That amount gets me through a full day.As far as connectors go,I would love to see see something that doesn't use the little plastic washer to separate the posts.I hate when I melt or break them.
Yup, I like that idea too... as long as it's not really long, then it just adds way too much length to some PVs which are already borderline too long as it is.
Hey cos, I just noticed your sig... you have two Hybrids?? You lucky SOB.... lol!
Yup, I like that idea too... as long as it's not really long, then it just adds way too much length to some PVs which are already borderline too long as it is.
Hey cos, I just noticed your sig... you have two Hybrids?? You lucky SOB.... lol!
NatureBoy yeh i have 2. 1 for each hand.
- Status
Similar threads
