Tailpiping 801s

[boochips]

I don't know if I am the only one but I am curious about it. I tried the tailpipe thing a couple weeks ago and now I cannot stand to vape my Prodigy 801 with a mouthpiece on it at all. I wish I could find a mouthpiece I would like again because I look like a crackpipe smoker at work! LOL Anyone else or just me?

 

[vapn]

That's the only way I can use the 801 also... I think Steve does it too...lol.. I get a much better hit that way. So you are not alone. I was even thinking about using some of that plastic stuff you dip tool handles in to help with the possibility of cutting my lip on it by accident. Haven't tried it yet though. I am stuck on the 510 now so haven't used the 801 in a while.

 

[CaSHMeRe]

same here ... discovered tailpiping ... mouthpiece is a waste of rubber now ...

 

[Mr-Glass]

same here ... discovered tailpiping ... mouthpiece is a waste of rubber now ...

Funny - agreed - I always tailpiped my 510's damn they get hot - bought a few 801s and the 510 to 801 adapter - and I must admit it is nice on the 801 not getting so hot.. still love my 510s the best tho - I thought the plastic mouth piece was just to keep pocket lent from getting into your atty... lol

 

[CaSHMeRe]

very very true on the pocket lint mr glass .... hmmmm

I tried tailpiping 901's and 510's ... a bit *too* hott for me. The months I went tailpiping the 801 at 6v's, I swear, I was getting dead lip skin on the atty from the heat ... Any of you tailpipers know what I mean, or do I just suffer from dry lips ?!?!?! LOL ... I would take my fingernail and run it along the outside to clean it!

 

[vapn]

You can use those little rubber pieces that come on the cartomizers for the 510. I cut a slit in the end of it and they slide on and stay there. Helps get more airflow and cuts down on the heat. I think you can get them for 2 cents a piece if you don't use those. Don't remember where though.

 

[Stormynights]

My daughter made fun of me for this now she is doing it too. I think I found a good cart filler finally so I may stop.

 

[vapn]

I don't think the cart design is good no matter what filler material you use. It is a sponge and the only way to get all the juice out of a sponge is to squeeze it. I think they are a waste of juice and that is too valuable these days. Every drop counts and I like vaping every bit of it. After I squeezed out 12ml from my "Empty" carts I started dripping only.

An after thought...
Steve, why don't you come up with a mouthpiece we could slip on the end of a 510, 901, 801 that would help with the heat and open up the airway just like tail piping would be. I bet it would go over well. You could use delron or something like that. Put an o ring inside it to keep it in place. Hmmm...

 

[boochips]

An after thought...
Steve, why don't you come up with a mouthpiece we could slip on the end of a 510, 901, 801 that would help with the heat and open up the airway just like tail piping would be. I bet it would go over well. You could use delron or something like that. Put an o ring inside it to keep it in place. Hmmm...

Great idea vapnaway, how about it Steve?

 

[vapn]

I just thought of another reason I want something like this. So I don't have to take it off to drip. That is annoying me. I might just have to try cutting a regular mouthpiece to do away with the small hole in the end. Especially when driving this would come in handy. You have four things in your hands, the PV, mouthpiece, bottle, and bottle top. Now just for a self sealing bottle top.... hmmm... the ideas never stop.

 

[panderson01]

Tail piping is the only way to go. I can never go back to mouth pieces or carts.

My atty is connected to the 5+ volt Prodigy.

Now I just need to figure out what to do with my extra carts?????????????

 

[boochips]

Tail piping is the only way to go. I can never go back to mouth pieces or carts.

My atty is connected to the 5+ volt Prodigy.

Now I just need to figure out what to do with my extra carts?????????????

I know what you mean panderson....I bought 100 carts from china before my prodigy got here and now what to do with all of them...lol

 

[Dr. Russell Fell]

i tried this method (never thought to call it "tailpiping), and it was just too awkward for me. i'm fine with the rubber mouthpiece.

for an idea of a possible metal mouthpiece, check this out.

 

[buckfill]

"Tailpiping"! That is damn near hilarious and a great term for taking the mouthpiece off. The funny thing is that i NEVER would have thought of doing something like that until last weekend. I was sitting on my neighbor's deck and my friggin mouthpiece rolled off the table and down into a crack while i was reloading. My neighbor asked what I was going to do. Little did I know...i was "tailpiping"!!! We got a good laugh and I got a really good vape!

 

[illspeed]

I actually dont like tail piping, I prefer the smoother controlled draw through a mouthpiece. I dont like the rubber mouthpieces though. I like the hard plastic ones that come on the totally wicked Attys but use the mouthpieces on the puresmoker atty. That and it dries my lips out too much.