Mike I did get one to fit but I can't get any of the others to fit. So I would not buy the Sleeve just to use with a drip shield.
- Status
Alright finally snagged one of these for the i06.It's gonna be nice not using the stock tips anymore.
I am using i06 on a REO. Anyone else have success with the sleeve and this combo? It would be heavenly to use my DTs.
Sent from my iPad using Tapatalk HD
Sent from my iPad using Tapatalk HD
Sleeve isn't going to have a negative effect on the fitment of the io6 with the Reo. It only changes the way you use the io6 re: drip tips. Also will make your vape a tad cooler.
They do not fit inside an empire dripshield.
Just got mine in. Tried to stick it in the empire shield from the bottom like i do with the iken dt's, no dice.
BUT, I loaded it into the shield from the top and boom, it fits!!! WHOOO HOOO!!!
Got mine in today
Slapped in a fresh i06, screwed it onto a Reo grand, popped on a Trippy Tip and SHAZAM! Works like a charm.
Easy as pie....well done, it's a win.
Slapped in a fresh i06, screwed it onto a Reo grand, popped on a Trippy Tip and SHAZAM! Works like a charm.
Easy as pie....well done, it's a win.
JD-so glad you posted about the shield. I have started to go through mine and found it actually will slip into a couple of mine that are from the hex line. It's tight and I have to use a pen to get it out, but it will work!
Wharf, the sleeves punch nicely for a feed tube. Io6, sleeve, vvpv = vaping bliss
Very cool JD you got the drip shield to work and you too G8rGrl
I'm glad they're working so well for you DD & Enut !!!!
Too cool Mark. I guess I'm going to need one of those tools
I'm glad they're working so well for you DD & Enut !!!!
Too cool Mark. I guess I'm going to need one of those tools
Got mine today. My preferred size is that of the IKV 510 atty for UFS short mode with mouth piece. I'll cut these down this weekend. But additional sizes would be could.
Lesson learned today: If one wishes to see what the insides if an iO6 looks like, place this on extra tight and try and remove. - Oh look, red wires.
.-Z
"Lesson learned today: If one wishes to see what the insides if an iO6 looks like, place this on extra tight and try and remove. - Oh look, red wires."
I've seen them too -- with the original tips.
The first IO6 I saw I said how do you use it. They can't be dripping in that little tiny hole. So I pulled the tip off and it came apart. Now I was really stumped. I saw the wires and thought what the H. E. double toothpicks is this damn thing. This was one Isaac sent to me before they came out. and I couldn't for anything figure out what was going on.Got mine today. My preferred size is that of the IKV 510 atty for UFS short mode with mouth piece. I'll cut these down this weekend. But additional sizes would be could.
Lesson learned today: If one wishes to see what the insides if an iO6 looks like, place this on extra tight and try and remove. - Oh look, red wires.
-Z
Cut mine down with a tube cutter to fit a UFSv2, and primed it. A few bad hits as I got things tuned and vaping nirvana began. My quest is over, there is no need to look further.
Thank you, Isaac/Wharf
Be cool to see a future design that had an o-ring 'locking' mechanism, but this works, and works well. Only problem is I don't dare remove until the atty dies, else risk damaging the atty.
A limitation I can accept for now.
-Z (In vape heaven)
Thank you, Isaac/Wharf
Be cool to see a future design that had an o-ring 'locking' mechanism, but this works, and works well. Only problem is I don't dare remove until the atty dies, else risk damaging the atty.
A limitation I can accept for now.
-Z (In vape heaven)
Cool Z, I'm looking at a 28mm version for the UFS.
BTW try twisting clockwise (you probably have). I fit each one on 2-3 attys to test and the real tight ones twist off for me.
BTW try twisting clockwise (you probably have). I fit each one on 2-3 attys to test and the real tight ones twist off for me.
The first IO6 I saw I said how do you use it. They can't be dripping in that little tiny hole. So I pulled the tip off and it came apart. Now I was really stumped. I saw the wires and thought what the H. E. double toothpicks is this damn thing. This was one Isaac sent to me before they came out. and I couldn't for anything figure out what was going on.
Me too! I was like WTH, there is NO way I can drip in that hole!!! Which begets my question; how do I take the plastic off without ruining the atomizer? Can I cut it from the top? Just got my sleeve yesterday (thanks Wharf), but haven't had a chance to use it--I'm scared I'm going to ruin the atomizer trying to remove the plastic from it!
I used a slight twisting motion to get the plastic piece off. Alternately, if you have a bit of PG around, you could probably drip some in with it held at an angle, rotating it, to act as a lube.
- Status
Similar threads
