Sorry, I've been through that reference guide I don't know how many times as well, great piece of work
Thanks for contributing as well, much appreciated
- Status
Sorry, I've been through that reference guide I don't know how many times as well, great piece of work
Thanks for contributing as well, much appreciated
I am on the list for a v3...hope they are okCheers Crash, it is getting better or me getting more used to it this morning, the old Grants vanilla custard is very smooth through it 50/50 blend. I Have my name on the orion but there is some bad reports over here about them
1 wick hole not lining up
2 units marked on delivery
3 bad switches
4 leaking
So i have decided not to get one know, and become a Ihybrid nut
I have a 2.1 and it works great
I have not been boarding in about 5 years. kinda scared to do it again lol...
the list master
I want to test out some MNKE batteries. I found a couple places that sell MNKE 18650 batteries, but do you guys know of any places that sell other sizes?
Hey Todd, did you get around to modding your switch?
Sorry, I've been through that reference guide I don't know how many times as well, great piece of work
Thanks for contributing as well, much appreciated
I've been wanting to push the limits also lol. Did you check RTD? If I remember correctly they only had 1 or 2 sizes so maybe that's where your talking about.
Morning guys
I have only found and own 18650 and 26650 MNKE batteries.
If you need info pm me
The only other size that I know of is the 26650 MNKE and RTD carries those. I have a pipe that uses them and they are beyond impressive. Barely any voltage drop under load and they last for two days of vaping. 60 AMP max discharge. Fantastic.
Last time I looked MNKE does not make anything below 18650.
I've tried the three major styles of wick, straw, dual, and tight wrap. In my experience the last wick I made has been the best performing of them all. Its 3 inches of 400 mesh rolled so tight there's no central channel.
I'm vaping a high vg 30/70 juice and it's knocking my socks off, I know it'll be even better with 500 mesh. As for the coil, a good rule of thumb is the thicker the wick, the lower the resistance you'll need. It takes more heat to get a fat wick up to temperature... I'm current running at .8 ohms.
Btw, that .8 ohm coil is 28ga 4/3 offset wrap.
what did the od of it come out too?
I rolled 3 inches of 500 and it had a paperclip sized hole and filled the hole all the way in the ihy
Few setups for the wicks here
https://docs.google.com/spreadsheet/ccc?key=0Atm-i6EmP-hudG9XQ3ZHNXBNUndUaFFzZU1SdXhDeEE#gid=0
Nice bookmarked.
From my phone
It fills around 90% of the wick hole. The trick is to roll it as tightly as you can by hand, then roll it tighter by using two blocks of wood to get it entirely solid. When rolling it between the blocks, roll it with the coil of the roll, not against it. The outer layers may come loose in the process, when that happens, use your fingers to get it tight again, then go back to the blocks. You'll notice the center getting tighter and tighter as you do this.
Charger I'll try to grab an extra on the next batch for you. for cost.
BTW sidewinders seem to be available at electronicstix
Last edited:
OMG!
I don't have a FP colored drip tip.....
sigh.
I guess I have to go spend money now.
I should probably wait 'til it's in my hands so I have color right there.
I don't have a FP colored drip tip.....
sigh.
I guess I have to go spend money now.
I should probably wait 'til it's in my hands so I have color right there.
Few setups for the wicks here
https://docs.google.com/spreadsheet/ccc?key=0Atm-i6EmP-hudG9XQ3ZHNXBNUndUaFFzZU1SdXhDeEE#gid=0
Thanks Todd,
Carl
Yep made that error on the red dragon
QUOTE=UnFettered_Soul;8298424]OMG!
I don't have a FP colored drip tip.....
sigh.
I guess I have to go spend money now.
I should probably wait 'til it's in my hands so I have color right there.[/QUOTE]
QUOTE=UnFettered_Soul;8298424]OMG!
I don't have a FP colored drip tip.....
sigh.
I guess I have to go spend money now.
I should probably wait 'til it's in my hands so I have color right there.[/QUOTE]
ugh, I just broke my 9/11 flag drip tip
Ouchie that sucks
Thats my biggest concern with glass drip tips, the only reason I havent broken several tanks is because of the tank protector lol
Ouchie that sucks
Thats my biggest concern with glass drip tips, the only reason I havent broken several tanks is because of the tank protector lol
I've had my iHy fall, with the tank protector on, and land on the tip. The tip was fine but the shock went to the tank and broke it. I always get mad when someone says I haven't broken a tank because I USE THE PROTECTOR. Like I'm stupid lol. My two tanks have broken: 1 with the protector and the second while dry burning(my orings were swelled). The protector defiantly has saved me a few times so I ALWAYS use it.
I'd assume its iHy LE one, not a matching glass
. Still cool, however!!!- Status
Similar threads
- Locked
