I'm not opposed to going that route. I just don't really know anything about them.
The Nicoticket Approved Delivery Device Advice Thread
- Thread starter taki1203
- Start date
- th_trl_thread_readers 0
- Status
A mechanical box mod that's nearly indestructible. It's bottom feed and depending on model has 6 or 3 ml of juice on board. With an rba it give the performance of dripping with the convenience of a tank. Almost everybody who tries them, says why did I wait so long and eventually sells off the other stuff and buys more Reos.
Head over to Reoville and check them-out. Reos Mods
Head over to Reoville and check them-out. Reos Mods
My Reo showed up today along with my order of Mah Peeps. Wrapped a quick 1.2 ohm coil and fired it up. MP's pretty good but a little to surgary sweet for an ADV for me. I also like a looser draw than the RM2 provides. Before I start drilling air holes I'm going to wait for the Chalice III to get here. All in all I'm impressed with the Reo.
The stock RM2 stock air hole is really sized for those used to a carto draw. I always drilled mine to 1/16. It's easy to do because of the plated brass of the RM2
I always hated cartos so that explains a lot. My Billet Box Didn't get near enough use until I got a Billet Bridge, now it's pretty much all I use. Remember when everyone said Zens had to big an air hole? Now everyone wants a 1/4" air hole and run .1ohms 
The Reo is my device of choice. You get all the performance of a dripper without the hassle. It's dripping from the bottom.
It is a mechanical box mod that holds a battery and a bottle of liquid that feeds through a tube to the atty through the 510 connection. You do need to have a bottom fed atty for this to work. Give the bottle a squonk (that's what we call squeezing the bottle) and juice goes up to wet the wick. Press the fire button and vape away.
I drive a lot, so with the Reo I get to drip and drive without praying for red lights...
It is a mechanical box mod that holds a battery and a bottle of liquid that feeds through a tube to the atty through the 510 connection. You do need to have a bottom fed atty for this to work. Give the bottle a squonk (that's what we call squeezing the bottle) and juice goes up to wet the wick. Press the fire button and vape away.
I drive a lot, so with the Reo I get to drip and drive without praying for red lights...
It's brass, so you don't need a drill press. You can do it with a knife tip or something similar . . .
Do you have a regular drill? That's all I used to drill out mine. It's plated brass which is really soft and easy to drill by hand. I just held the cap with pliers I taped up so I would not scratch it. I started with a 1/16th and then went to 5/64ths after trying the 1/16th. I'm not a metal shop worker and don't play one on TV so you can do it!
I have a drill but will have to get a 1/16th drill bit for it. It belonged to my late brother and all I've used it for is putting stuff together. I may try Keith's suggestion. I have knives! Lol
don't slip, a drill bit will be safer and only cost a couple of bucks for a cheap one, IIRC it was 3 or 4 for two at home depot
I'm going to leave the RM2 alone for now. Drilling it is no big deal but it may end up in the classies once my Chalice III gets here.
I found some kind of weird looking screwdriver(?) this after when I was looking for an Allen key. It's L shaped with sharp point on the end. I put that in the whole and wiggled it back and forth while putting pressure on it. Now the air hole is perfect! Not too big, not too small. 
Just be careful with the knives. We don't want to hear about a trip to the hospital. The drill would produce a cleaner and precisely sized hole though.
congrats!I found some kind of weird looking screwdriver(?) this after when I was looking for an Allen key. It's L shaped with sharp point on the end. I put that in the whole and wiggled it back and forth while putting pressure on it. Now the air hole is perfect! Not too big, not too small.
Thanks!!
I would have been scared using the drill. I only wanted the hole enlarged just a little. As uncoordinated as I am at times I may have drilled air holes in both sides.
It's the end result that counts, not the method in this case.
Finally got my Challice III built and running on the reo mini. Sporting a Dready custom for the event.
Not the best vape porn pic, but had to share the joy. This setup is amazing. Lovin the mini and the C3. And of course it wouldn't be the same without Dready's amazing work. Thank you Mark, Mark, and Rob. True masters of their craft.
EDIT: Completely neglected to mention the secret ingredient! 8-o
ACB from the September batch with old skoolz TA - had to break out the special sauce for the occasion. No magical mod combination is complete without good NT juice of course. Speaking of which it's time for a refill!
Awesome set up Scratch! Congratulations!
I'm the only one around here with the talent to open a xmas gift and sever a tendon in my thumb at the same time . . . ..
- Status
Similar threads
