"The Russian" 91% (Kayfun Lite Clone With A Twist)

[kurtus]

Well 4 month wait is finally over and hells yeah it was worth it, used a green scotch brite pad followed with a quick shot of autosol polish, 10 minutes later and it is a very close brushed match to the nemy.

 

[Bern Diesel]

That came out clean and the logo is still visible. I keep tellin people don't trip on the finish and it doesn't require power tools or sandpaper to brush it yourself. Good job! I expect mine this week also. Hopefully tomorrow

 

[Chadastrophic]

I swap between my 91% and kfl+ almost hourly, every time I put the 91 back on I have to unscrew the center pin a little. If I don't the ohms jump all over the place. Any fix to keep the center pin in one spot better?

Sent from my SCH-I605 using Tapatalk 2

 

[proraptor]

I swap between my 91% and kfl+ almost hourly, every time I put the 91 back on I have to unscrew the center pin a little. If I don't the ohms jump all over the place. Any fix to keep the center pin in one spot better?

Sent from my SCH-I605 using Tapatalk 2

I put a little noalax on the threads of the pin and dont have this problem

 

[toolguy420]

Hey now! Does anybody know of a link to the Russian 91% manual that they could share? I have searched via Google with no luck. Thanks!

 

[Chadastrophic]

Hey now! Does anybody know of a link to the Russian 91% manual that they could share? I have searched via Google with no luck. Thanks!

Just go to the svoemesto website and check out the kfl manual.

I put a little noalax on the threads of the pin and dont have this problem

Thx! I'll try that.

Sent from my SCH-I605 using Tapatalk 2

 

[savagemann]

Did a quick test run brushing the 2 tank pieces with a green dish scrubber.
Will complete it later, but it is super easy.
I spent about 2 minutes on it.

 

[bradysyde]

I polished mine.

 

[toolguy420]

Just go to the svoemesto website and check out the kfl manual.

Appreciate it! I was pretty sure they were one in the same; thanks for verifying.

used a green scotch brite pad followed with a quick shot of autosol polish, 10 minutes later and it is a very close brushed match to the nemy.

Did a quick test run brushing the 2 tank pieces with a green dish scrubber.

Nice job, guys...are y'all using something to turn the pieces, or is it totally done by hand?

I polished mine.

Looks great!

 

[HandbananA]

Hand


Tapatalk

 

[savagemann]

Toolguy, I just stuck the tank pieces around the end of my thumb so it wouldn't spin, then took the green scrubber to it in smooth long strokes.

 

[Exhaler]

I've been trying to figure out what metal is below the annealed finish. It's so light I think parts are aluminum but looking at the pictures of the 91's that have been brushed they look like maybe thin SS? But then again, they are releasing a SS version next, so I give up, what is it?

 

[Innocuous]

Over & over & over.. We keep telling folks:
....It's Stainless Steel;
....It's Media Blasted;
....You can polish it with a 3M pad;


Why is this so difficult to read and acknowlege?

Going on two weeks now with the same little NR/R wire verticoil, cotton replaced once. Just yummy lung-drags.

 

[mocha_jo1]

I've been wanting a KFL+ or Russian 91% for a bit now, and are hard to get online. I went to my local b&m and came across a 91, and had to buy it. I think I'm in love. I was a genesis guy, but I think I've come to the dark side now!

 

[Exhaler]

I've been wanting a KFL+ or Russian 91% for a bit now, and are hard to get online. I went to my local b&m and came across a 91, and had to buy it. I think I'm in love. I was a genesis guy, but I think I've come to the dark side now!

I have my share of Genny's and the Russian, still I believe good RDA's are the best vapes. They can be a pain, but worth it IMHO.

 

[mocha_jo1]

I have my share of Genny's and the Russian, still I believe good RDA's are the best vapes. They can be a pain, but worth it IMHO.

I have a few different drippers, but am too lazy to drip all the time. I haven't played with them too much though. Know a good setup that will hold a lot of juice?

 

[Innocuous]

You *do* realize that SM sells a chimney and tank extension, right? And they are stackable? ;-)

See vaperev

 

[pizza2me]

Over & over & over.. We keep telling folks:
....It's Stainless Steel;
....It's Media Blasted;
....You can polish it with a 3M pad;


Why is this so difficult to read and acknowlege?

Going on two weeks now with the same little NR/R wire verticoil, cotton replaced once. Just yummy lung-drags.

Why use NR/R wire in a kayfun type atty? for less wasted resistance?

 

[nelsonm64]

anyone interested in a 91% clone? looks good and, comes with both clear and steel tank and, you get a choice or polished or brushed stainless steel. i ordered one. excellent price... now i'll have a real one, a clone and, a clone of a clone LOL.

Russian rebuildable atomizer

 

[godowar]

ALCON,

Well I finally got my Russian 91% in a few weeks ago. Been vaping it like a choo choo train, and this thing is great! My only gripe, and I am asking for a little advice here ... Is after I have been vaping on it for awhile I seem to get juice buildup between the topcap, and driptip. Now I can unscrew the tip, and wipe it clean and give it a quick blow ... But it gets annoying to be vaping happily along, and then get juice in my mouth.

Any ideas?