Ufs -> 510
- Thread starter Siarek
- Start date
- th_trl_thread_readers 0
-
- Tags
- provari vaporkings
- Status
Ordered mine Oct. 4. Just received it today. Threads had a couple of little burs, but I was able to scrape them out well enough with the tip of a crappy old pocket knife.
In any case, for any of you who have gone a month after ordering with no news, just be patient. You'll eventually get what you ordered.
In any case, for any of you who have gone a month after ordering with no news, just be patient. You'll eventually get what you ordered.
Mine is a little touchy, but that probably has more to do with the recessed 510 connection on my Precise Plus. I just have to make sure to screw the adapter onto the battery mod first, then screw the UFS onto the adapter, being careful not to over-tighten.
The adapter works for me. Now I just need to figure out how to fill and feed with the UFS without getting a mouthful of juice.
The adapter works for me. Now I just need to figure out how to fill and feed with the UFS without getting a mouthful of juice.
(Posting to these forums using a Kindle isn't as easy as I make it look.)
Last edited:
Close the juice controll and vape till your atty or carto is dry. Then just bairly open the juice controll 1/8 of a turn or so do a prime puff to get a little juice in it then vape till it is dry again and repeat. Once you find that you are flooding the atty or carto every time you take a hit then you have opened the juice controll to much so back it off a bit.
reffiling has to be made with air and liquid closed rojo. Also you screw first the big cap, then put the o-ring, then the small cap. Then you open only air to vape. Dont open the juice control before you take 2-3 puffs first to see the situation of the atomizer. If its flooded then you keep liquid closed until you vape the exessed liquid. If you have a burn taste then you open the liquid at 1 full turn and check again your vape
Update: On my adapter, the battery connector was snapped into the center of the body of the adapter, but was not permanently fixed. There appeared to be a small puddle of solder in the center recess of the machined body, like whoever made the adapter missed with the solder but didn't know it. It's hard to describe, but the end result was that the inner bit of the adapter easily detached from the outer bit.
I had to sweat some more solder into the seam (however crudely) between the manufactured 510 battery connection and the machined main adapter ring to get the adapter to stay together. It's not pretty, but at least my awful rookie soldering is hidden inside the 510 overflow tank. Now tightening the adapter into the UFS doesn't encourage the center bit to pop out, and it's a lot sturdier laterally and my fully-assembled PV won't break in half.
Maybe one of these days I'll take a picture or two to show you what I'm talking about. My new daughter is keeping me pretty busy lately, so I'm not sure when that will be.
Any one have a spare in the us they would be willing to sell?
Sent from my PC36100 using Tapatalk
Sent from my PC36100 using Tapatalk
I'd like to know the same thing although I think I am probably just going to break down and buy one. I really wish I had access to a machine shop to make one.
I plan to order a few when the next run is made but can't wait to use the Ufs on my provari
Sent from my PC36100 using Tapatalk
Sent from my PC36100 using Tapatalk
Iv sent a few emails. First one got a response back with in one hour telling me he will have them next week( this week) and he will get back to me In 2h.. that was last week and iv yet to hear back. I hope he comes through with them.
Sent from my PC36100 using Tapatalk
Sent from my PC36100 using Tapatalk
I just emailed him and he replied in less than 10 minutes.....He told me they should be shipping next week.
He also emailed me stating the same thing. I'm excited as ill have a Ufs provari and another set up as a back up..
Sent from my PC36100 using Tapatalk
Sent from my PC36100 using Tapatalk
still waiting :/
hopefully this is the week.
You should get yours soon, it might just be lost in the mail system. Unless you have talked to him and he is sending a replacement to make up for you not getting it in the first place. He is a very honest and just wants the best for everyone, I'm sorry it's taking so long to get it.
- Status
