xvostick clone any owners?

[DPLongo22]

You can download the help guide from http://www.evolvapor.com/datasheet/dna40.pdf

I haven't read through it, but I would expect all answers are there.

 

[mgmrick]

You can download the help guide from http://www.evolvapor.com/datasheet/dna40.pdf

I haven't read through it, but I would expect all answers are there.

Yes thanks I have read those instructions and have been using those. Nothing is written in their about temp off. There is a temp off setting for this chip in 3f's xvostick style mods. Might need to be the setting needed for running 3f's mods in power mode

 

[DPLongo22]

Yes thanks I have read those instructions and have been using those. Nothing is written in their about temp off. There is a temp off setting for this chip in 3f's xvostick style mods. Might need to be the setting needed for running 3f's mods in power mode

Really? I'd be surprised if it were there, yet not documented, but I've been surprised before in this world. Maybe shoot an email off to Evolv?

 

[jmarkus]

Yes thanks I have read those instructions and have been using those. Nothing is written in their about temp off. There is a temp off setting for this chip in 3f's xvostick style mods. Might need to be the setting needed for running 3f's mods in power mode

yes, authentic evolv has the same thing. scrolling past 600f on evolv chip turns temp off.

 

[ian91]

You can download the help guide from http://www.evolvapor.com/datasheet/dna40.pdf

I haven't read through it, but I would expect all answers are there.

Thanks, DP. This is what I was looking for. Looks like the clone has the same functionality as the real Evolve chip. Go figure!!!

 

[DPLongo22]

Thanks, DP. This is what I was looking for. Looks like the clone has the same functionality as the real Evolve chip. Go figure!!!

Sounds good to ME, Ian!

 

[mgmrick]

Setting temp off did not make ohms too message go away. However it vapes just fine with error message

 

[ian91]

FT's version does not mention temp control.....does it not have temp control?

I read on their forum this morning that the FT version does have TC. FT confirmed it. FT has a habit of screwing up descriptions of new items.

 

[ian91]

Setting temp off did not make ohms too message go away. However it vapes just fine with error message

I am now getting the ohms too high message as well since I turned off temperature control. My settings are 14.5watts with a 1.21ohm coil. I put in a different RBA with a 1.07ohm coil and am not getting the message. Is there some limit for resistance?

 

[ian91]

I reinstalled the 1.21ohm coil and am not getting the ohms too high message??? Too strange!!! I have read too many threads where people drive themselves crazy fiddling with this stuff. I am just going to accept the quirks and vape on!!!

 

[roxynoodle]

Both the authentic and clone chips are goofy and show odd messages, yet continue vaping fine. Which shows just how well they cloned that chip, lol! Its just best not to look at the screen.

 

[mgmrick]

Great location for screen...on bottom..can't see it...lol. yes it vapes just fine not an issue . Just pointing it out. Not an issue for me either

 

[pauljbl]

How is temp control working on it with ni200 wire?

 

[ZeroOhm]

Does an evolve dna40 chip have a temp off setting?

Yes, I am hoping someone will have fitted a genuine evolv in the clone by the time mine arrives The only clone board DNAs I think are any good are the Kangxin and SKX, the board in the SKX Zero mini looks spot on but a little long winded and expensive to get a clone board to put into a Xvo clone.

 

[Vlad 234]

 

[arth_d]

About to push the button and get one of these. And I also have to buy some 18650's to go with it. Just wondering if the mod is picky with what type of batteries it accepts. Only flat tops? Only nipple tops?.
What are you guys using?

 

[drugarth]

in the authentic I am using flat tops......with mods flat tops are the safest bet they wil fit...use them in all my mods...samsung 25r or sony vtc4 or 5 are good

 

[1ceCreamMan]

I can't wait for mine to come in

 

[DPLongo22]

in the authentic I am using flat tops......with mods flat tops are the safest bet they wil fit...use them in all my mods...samsung 25r or sony vtc4 or 5 are good

I've used both (in authentic). The battery cap sticks up a touch with my buttoned ones, but they both work fine.

 

[Flt Simulation]

Well, I wonder if there are any differences between the XvoStick clones sold by FastTech and 3Fvape, or do you think they are both the same and manufactured by the same Chinese company?

There is a difference in price:

FastTech: $ 46.25

3Fvape: $ 51.99