Zenesis Informational/Help thread. Please Post questions and answers here.
- Thread starter applefr3ak
- Start date
- th_trl_thread_readers 0
- Status
That's super info, thanks so much !
Just one little question more....when mine flew into pieces, it appears there were 2 springs.....one which remained on the botton post of the button, and a graduated one that flew off but I found again...any advice on where I place that?
mine only has 1 spring, upload a picture of the 2 springs on the same pic
Enviado desde mi iPhone con Tapatalk
It's ok man, I followed exactly as you said and lost the spring that I thought had popped out and reassembled and all is working fine now.
You're a star man!
Now, off to try and tackle to the sub ohm kit later!
You're a star man!
Now, off to try and tackle to the sub ohm kit later!
the only Zencessories they have are the ones sold on Stixelectronics and one button switch. I am wondering if anyone knows of any non-510 attys or cartos anyone has found that work with the zenesis2.
yes electronicstix is the main distributor, you can look for compatible stuff on steammonkey.com not much tho, just a dripper and button switches, and brass tubes with a monkey so alike the owner but shaved lol
Enviado desde mi iPhone con Tapatalk
Enviado desde mi iPhone con Tapatalk
Hi everybody,
I know that this question has probably been answered a million times but I just want to make sure that I don't mess up my device before making alterations so I have to ask first. I just purchased an Altus. The switch does not work. I contacted electronicstix.com and they were not able to help me or return my money. Tried to call the number on the House of Hybrids site as I was told to do by the vendor and left a voicemail. No one has called me back. I now have a $250 paperweight.
The support guy at electronicsitx said that I have the new switch so the instructions I've seen in the past might not apply and it is hard to read thru the 50+ pages here. Any assistance would be greatly appreciated.
Very frustrated,
Cybersue
I know that this question has probably been answered a million times but I just want to make sure that I don't mess up my device before making alterations so I have to ask first. I just purchased an Altus. The switch does not work. I contacted electronicstix.com and they were not able to help me or return my money. Tried to call the number on the House of Hybrids site as I was told to do by the vendor and left a voicemail. No one has called me back. I now have a $250 paperweight.
The support guy at electronicsitx said that I have the new switch so the instructions I've seen in the past might not apply and it is hard to read thru the 50+ pages here. Any assistance would be greatly appreciated.
Very frustrated,
Cybersue
well you should dissassembly your switch and take one washer out ir maybe add one.
Enviado desde mi iPhone con Tapatalk
Enviado desde mi iPhone con Tapatalk
Thanks for the suggestion. I've been reading through this thread and already tried this with no success.
Hello. What is it exactly doing? Are you making sure to push the switch into the side of the tube? ( not straight up from the middle). What kind of battery? Tell us more, and maybe we can figure it out
The switch does not work at all right now. It arrived on Thursday and maybe I was able to get 2 good clouds off of it in all that time. Each drag seams to be some percentage of the total power coming off the battery. I tried it with one more and one less washer and with and without the second spring. I use the IMR 18650 batteries (button top) and have been trying to hit that damn button in any way possible to get it to work. There seams to be only the slightest amount of throw with three washers in, better with only 2 but not enough to make contact.
I'd hate to have to sand down the screw because of the gold plating but I will do it if it needs to be done. Any other suggestions like purchasing new parts from the hardware store?
I did not receive a call back from HoH and I don't expect one over the weekend. It's very frustrating because this is my first high end mod, I had heard so many good things about the Zenisis system as well as the fact that it is fiddly but I'm not an electrical engineer and am concerned that I'll never get it to work.
Thanks for any help you can give. All suggestions are greatly apprieciated.
I'd hate to have to sand down the screw because of the gold plating but I will do it if it needs to be done. Any other suggestions like purchasing new parts from the hardware store?
I did not receive a call back from HoH and I don't expect one over the weekend. It's very frustrating because this is my first high end mod, I had heard so many good things about the Zenisis system as well as the fact that it is fiddly but I'm not an electrical engineer and am concerned that I'll never get it to work.
Thanks for any help you can give. All suggestions are greatly apprieciated.
Also the coil takes a long time to heat up on the occasions that the switch does happen to make contact and then I only get a small puff.
Is it possible to ruin my batteries by testing with them so much? The bottom of the tube does warm up after about 20 tries to get the switch to work and I stop.
Is it possible to ruin my batteries by testing with them so much? The bottom of the tube does warm up after about 20 tries to get the switch to work and I stop.
I've also built the coil several times to rule that out and made sure that there aren't any shorts.
I've summoned some facebook folks. Hopefully we can help you get it sorted. What happens if you don't use the delrin cup in the switch? Just try the spring that is not cone shaped without the delrin cup. use two washers with this, as this resembles the old switch. If that doesn't work, then I'd say you may need to have Mike send you a new screw
- Status
Similar threads
- Locked
- Locked
