Pioneer4you iPV V200 200W Dual 18650 Box Mod is made of zinc alloy, anodized aluminum, and ABS, which is strong and durable.

Pioneer4You iPV V200 Mod uses dual 18650 batteries (not included) and the maximum output power is 200W.

The iPV V200 BOX Mod is powered by the waterproof YIHI SX531 chip. This makes the Pioneer4you iPV V200 Mod not only has a fast-charging function but also has a certain waterproof effect, which provides protection for your safe use. Using the 0.96 inches TFT screen, you can clearly see the vaping data. Five flavor curves can be customized on the smart device side, namely Soft, Normal, Strong, custom SXi-EQ curves, EQ1-EQ3.

Features:
510 threading connection
Material: Zinc alloy & anodized aluminum & ABS
Battery: dual 18650 batteries (not included)
Power: 5~200W
Resistance range: 0.1~1ohm
Voltage: 6.4~8.4V
Charging: Type-C, 5V/ 2A
Quiescent current: <100uA
Flavor curve: soft, normal, strong, custom SXi-EQ curves, EQ1-EQ3
Waterproof YiHi SX531 chip
Dual 18650 batteries, max 200W output
0.96 inch TFT screen
Intelligent on-device customizable flavor curves
5 digit puff counter
Interchangeable magnet side battery doors
5V / 2A fast charging
30mm 510 connector
Low battery protection
Battery over-charge protection
Time limit ignition protection
Overheat protection
Low resistance protection
Short circuit protection
Reverse polarity protection

More details for IPV V200, please check >> https://www.3fvape.com/52805-pioneer4you-ipv-v200.html

Compared with the other Marvos Series Kit(Marvos S 80W, Marvos 60W, and Marvos T 80W), how do you like the Marvos 80W Kit? Being equipped with the industry-leading mesh coil technology FM COILTECH4.0, it also features Slide Airflow Control, Three Output Modes (Power, Smart & Bypass), Anti-spitback 810 Drip Tip, Single 18650 External Battery, 2A Type-C Fast Charging and all-around metallic design.

All of these features make the Marvos 80W kit even better than the best sub-ohm mod kit in the market. As for you, which feature can attract you to buy the Marvos 80W Kit?

Pioneer4you IPV U710 80W Box Mod is constructed of zinc alloy, aluminum and plastic with ergonomic shape.

IPV U710 Box Mod is powered by single 18650 battery (not included) with max 80W output and 2A Type-C quick charging.

Pioneer4you IPV U710 features waterproof and powerful YiHi SX710 chipset with 3 preset flavor curves (soft, normal, Hard) and 3 freely adjustable EQ Flavor Curves (Curve Mode). And Pioneer4you IPV U710 Mod is equipped with 0.96 inch TFT color screen to show vaping data and compatible with up to 24mm diameter tanks.

Features:
510 threading connection
Material: zinc alloy, aluminum and plastic
Battery: single 18650 battery (not included)
Output: 5~80W
Steam modes: VW / Power mode
Screen: 0.96 inch TFT color display
Quiescent current: <10uA
Max charge: 5V / 1A
Compact single 18650 battery box mod
Modern design and ergonomic shape
VW / Power modes
Adjustable wattage of 5~80W
2A Quick-Charge by USB Type-C
Waterproof and powerful YiHi SX710 chipset on board
Extensive security features: Protection against overheating, polarity reversal, overcharging, deep discharge and resistance that is too low
3 preset flavor curves (soft, normal, Hard)
3 freely adjustable EQ Flavor Curves (Curve Mode)
User-friendly user interface
Brilliant 0.96 inch TFT color screen
Comfortable operation via fire button as well as "+" and "-" selection buttons
5-digit puff counter and draw time display
Compatible with up to 24mm diameter tanks

More details for IPV U710, please check >> https://www.3fvape.com/52808-pioneer4you-ipv-u710.html

Geekvape Wenax S-C Pod System Kit has stunning appearance to catch eyes. Geekvape Wenax S-C Pod Kit is powered by 1100 built-in battery.
New finish with stunning new colors. New charge with Type-C port.
Upgraded cartridge for better MTL experience. New mesh coil adopted for smoother flavor.
With impressive 2 days use, Wenax Stylus is now shining bright like a diamond.
Geekvape Wenax S-C Kit features 3-level adjustable output and auto activation & firing button ignition. Geekvape Wenax S-C cartridge has 2ml capacity and is compatible with Geekvaep G Series Coil for MTL vaping.


Quick Link:
Geekvape G Series Coils

Parameters:
Size: 18.85* 112mm
Battery: built-in 1100 battery
Output: Auto activation-0.6ohm(14/15/16W), 1.2ohm(9/10/11W)
Firing button-0.6ohm(16W), 1.2ohm(11W)
Charging: Type-C, 5V/1A
Resistance range: 0.5-3ohm
Working temperature: -10-45℃
Longest vaping time: 10s
PCBA temperature alarm: 80℃
Low voltage warning: 3.2V±0.1V
Standby current: <15uA
Capacity: 2ml
Resistance: 0.6ohm(13-18W)
1.2ohm(10-12W)

Features:
Internal 1100mah battery, 3-level adjustable output
Auto activation & firing button
Type-C port
MTL experience

Packages:
1* Geekvape Wenax S-C Kit
2* Geekvaep G Series Coil(Pre-installed: 0.6ohm, 13-18W; Spare: 1.2ohm, 10-12W)
1* Coil Tool
1* Delrin Drip Tip
1* Type-C Cable

This thread is for the general discussion of the Pod Vape Geekvape Wenax S-C: Shining. Speedy. Smooth.. Please add to the discussion here.

Hi, i use drag x kit by voopoo with factory coils and recently i bought the rta ares 2 by innokin (and also the drag x adapter in order to put rta atomizer) so i'm new to rebuildable atomizers. The thing is that it doesnt read the ohm, i have to loosen the screw at the bottom of the atomiser in order to do and even then after some time the ohm disappear so i have to do it again. Also, when the above stabilize for some time and i'm able to take some vapes it's tasteless. Thanks in advance!

Hi,guys.Glad to introduce the Freemax Marvos 80W Kit which is inspired from Freemax world-known Fireluke Series.

The Vape Freemax USA Marvos 80W Pod Kit has 3-level adjustable power output by 3 clicks of the firing button. And the LED light will indicate the level of wattage. Secondly, the Freemax Marvos 80W Pod Kit utilizes a real 3000mAh internal battery with Type-C USB Port and 2A Fast Charging function. It only takes 90 minutes to charge from1% to 100%, which makes your device always have the power you need for a whole day of use.

Featuring the newly upgraded FMCHIP 2.0 chip, super-accurate power output, faster-firing speed, securer protections, the Freemax Marvos 80W Kit offers a smart. fast, stable vaping experience inside and out for you.

FreeMax Marvos 80W Kit SPECIFICATION
Size:26.9*34.0*130.55mm
Pod Capacity:4.5ml
Coil Resistance:0.15ohm/0.25ohm/0.35ohm/0.5ohm
Output Mode: Power, Smart, Bypass
Battery:External 18650
Output Voltage:0.7-4.2V
Output Wattage:5-80W
Material:Zinc Alloy+PCTG
Weight:126.8g

Hurry to vape shop online to make an order.

Quick Link:FreeMax Marvos 80W Pod Mod Kit

After half a year since the release of Novo 4, SMOK recently released a new member of Novo family - Novo 2S. To be the 6th member, what’s new for the Novo 2S? Today we are going to have a brief comparison with Novo 4.




SMOK Novo 2S

Main Features:
1. 1.8ml Capacity, with built-in 0.9ohm Meshed Coil
2. Bilateral U-shaped airflow channel for smoother smoke
3. 800mAh built-in battery, with stealth LED Indicator,support draw-activated
4. Armor series of patterns & ultra-thin design, pleasing to the eye

SMOK Novo 4

Main Features:
1. 2ml cartridge, side filling system; with airflow valve on the mod
2. LP1 coils with 3-sillicone rings structure to prevent leakage
3. 800mAh built-in battery, output power 5-25W
4. One-to-all button design, click 2/3 times to start power adjustment
5. IML surface craft of fluid-line patterns, beautiful & exquisite

Comparison

1. Novo 2S is obviously smaller.
2. The coil of Novo 2S is non-detachable, while the coil of Novo 4 is replaceable.
3. Novo 2S only has a LED Indicator on the body, while the Novo 4 has a one-to-all button(airflow valve & Power on/off & Power adjustment), 0.49'' screen and LED Indicator.
4. Novo 2S only supports activation mode, Novo 4 supports both button & draw activation mode.

If you want to have a very convenient device, without any setting, we suggest to choose Novo 2S. It is the best choice for newbies. And the price is more affordable.

Smok Novo 2S vs Smok Novo 4

Which one is more attractive to you? Please leave your comment down below.

Learn More: (remember login first to check better wholesale price)
SMOK Novo 2S
SMOK Novo 4

ElegoMall provides worldwide shipping and competitive price for all the customers, register on ElegoMall now to get your new user coupon and enjoy better price of more latest vape kits.

Hey guys, have any of you had a lung x-Ray after vaping for years? I’ve been vaping since 2015, still vape everyday on a sub-ohm tank and I feel great. Still workout at the gym, blood oxygen level is at 99% last few times I been to the doctor etc. I’m very curious to get a lung x-Ray just to make sure everything is ok out of curiosity. Let me know your results for those that have had it and post how many years you’ve been vaping.

Pretty sure this is all that remains of my wife's vaping gear after she quit. Very lightly used Eleaf iJust Mini 25W with a pack of GT M 0.6ohm coil heads. Also included but not shown is a microUSB charging cable. No box, sorry.

5 click on/off, three clicks to adjust power. It's a neat little stealth/pocket/starter set up. Coils are still readily available. Device is in excellent condition. Tank and AFC base have been ulttrasonically cleaned.

$20 $15 shipped. Payment via PayPal F&F or buyer assumes fees. Thanks!

The Pioneer4U IPV 200 is a return to the high power mods that IPV used to produce on a regular basis before their parent company (SXMini) went down the road of the auto squonker.

Pioneer4U IPV 200 - CHAPTERS

00:00 - Intro and specs
04:00 - Close up and build
11:00 - Vape
15:00 - Thoughts


Login to view embedded media

F.D.A. Authorizes E-Cigarettes to Stay on U.S. Market for the First Time
The agency approved three Vuse vaping products and said their benefits in helping smokers quit outweighed the risks of hooking youths.

"The Food and Drug Administration for the first time on Tuesday authorized an electronic cigarette to be sold in the United States, a significant turn in one of the most contentious public health debates in decades.

In greenlighting a device and tobacco-flavored cartridges marketed by R.J. Reynolds under the brand name Vuse, the agency signaled that it believed that the help certain vaping devices offer smokers to quit traditional cigarettes is more significant than the risks of ensnaring a new generation.

“The authorized products’ aerosols are significantly less toxic than combusted cigarettes based on available data,” the F.D.A. said in a statement announcing the decision.

The statement concluded, “The F.D.A. determined that the potential benefit to smokers who switch completely or significantly reduce their cigarette use, would outweigh the risk to youth.”


The watershed decision could pave the way for authorization of some other electronic cigarettes, including those of the once-dominant maker Juul, to stay on the market. For more than a year, the manufacturers of e-cigarettes have been in a holding pattern — most of their products on the market but awaiting official authorization — as the F.D.A. has investigated whether they were a benefit or a danger to public health........."

F.D.A. Authorizes E-Cigarettes to Stay on U.S. Market for the First Time

New Arrival | Digiflavor S G MTL Tube Kit


Parameter:

• Size: 22* 148mm
• Battery: single 18650/18350 battery(not included)
• Output current: max 7A
• Output voltage: max 3.7V
• Charging voltage: 5V±5%
• Recharging current: 1500mA
• Resistance range: 0.6-2±0.05ohm
• Short circuit protection: 0.4±0.1ohm
• Timeout protection: 10±1s
• Overheat protection: 75℃±5℃
• Charging: Type-C, DC 5V/2A
• Stand-by current: ≤ 30uA
• Operating temperature: 0-45℃
• Capacity: 4ml
• Resistance: KA1 1.2ohm(8-12W)
• KA1 1.8ohm(7-9W)
• Thread: 510

Package Content:

• 1x Digiflavor S Tube Mod
• 1x Siren G MTL Tank
• 2x G Series Coils(Preinstalled: 1.2ohm, Spare: 1.8ohm)
• 1x Spare Silicon Ring
• 1x Drip Tip
• 1x Type-C cable
• 1x User manual

I’m here today to present my second review for Hellvape. The Hellvape Dead Rabbit R Tank was sent to me for the purpose of providing a fair and honest review by Hellvape. You might be surprised to find out that I’ve never tried any of the Dead Rabbit series of tanks and have only tried a couple of tanks made by Hellvape. Testing the R Tank has been a very interesting experience for me. The R Tank is a bottom airflow tank and holds 5ml of liquid with the pre-installed straight glass and 6.5ml of liquid with the included spare bubble glass. It is in my opinion an attractive looking tank but I’m sure what you really want to know is how it vapes so let’s get to it.






WHAT’S IN THE BOX?






SPECIFICATIONS:



FEATURES:

1. New style meshed rebuildable tank

2. Quarter-turn top fill system

3. Knurled grip to assist bottom airflow adjustment easily

4. Changeable drip tip, 5ml/6.5ml capacity

5. One pack of R Coil accessories can be built the coil 10 times

6. Easy to build the coil with DIY fun










INITITAL THOUGHTS:

The packaging on this one is an eye catcher. The box is bright red with the Hellvape logo on top and the Dead Rabbit picture larger in the center. Once opened, the tank is exposed with the straight glass on it for shipping and the bubble glass below it in the foam insert. Actually what is seen first it the coil insertion instructions sitting on top of the tank and glass when the box is first opened.

The R Tank is very easy to disassemble for cleaning which I like to do before using any new tank. I was a little surprised that they went with a 510 drip tip but it seems to work out well. The top cap and the base both have a Celtic design wrapping around them. The top cap was very easy to remove for filling with a ¼ turn.

The first thing I did after cleaning the tank was to go ahead and install the bubble glass. I prefer to have the larger liquid capacity but the 5ml capacity with the straight glass isn’t bad at all either.





The internal chimney has R Tank printed on it which is easily visible through the glass. Above the airflow/ deck screw ring is the Dead Rabbit symbol on one side and on the opposite side is the Dead Rabbit name.





By now you might be thinking that this is just another regular RTA. Well, it’s not. The R Tank is not only a mesh coil tank but it is a vertical mesh coil tank. I find the base design rather interesting. The circular opening where the coil is inserted has multiple openings in it to allow plenty of liquid to flow to the cotton for the coil. Below where the opening is in the circular base there are two holes and when you turn the airflow ring it exposes two flat head screws that tighten down on the legs of the mesh coils.





First, you lay the included cotton strip down on a flat surface and place the mesh strip on it trying to center it as much as possible. It is important that you lay the strip with the cut corner on the top left. Then use the included coil tool with the side with the dimple sticking out upward and wrap the coil and cotton in one motion. Hold the cotton, coil, and tool securely and slide the coil down into the opening on the base. Don’t forget to loosen the flat head screws first so that the coil legs can go into place and then tighten the two screws. Clip the cotton as close as you can to the opening and you are done. Soak the cotton with liquid, fill the tank, and you’re ready to vape. I totally expected to have issues inserting the coil but had none. It was so easy that I was actually surprised at how well it went. Hellvape says it can be done in 15 seconds. I’m not sure about that but it went very quickly.







FINAL THOUGHTS:

I really enjoyed testing the Hellvape Dead Rabbit R Tank. I was a little skeptical at first about how difficult it was going to be to install a coil in this tank but it went smoother than I could even have imagined.

I think it’s a really great and interesting design. I’ve used a few other mesh tanks but had never seen a rebuildable vertical mesh tank like this. Even though the literature says you can build ten coils, there are only five coils and cotton strips included with the tank. However, if you buy the refill packs then you will get ten coils and strips for about the price of a couple of drop in coils.

On my first build, I didn’t get the cotton pushed down far enough on the bottom after cutting the cotton strip and got a bit of leaking after each refill. I knew pretty quickly what the cause was and installed a new coil and cotton strip. After that I didn’t have any leaking issues so it was purely operator error. I knew about pushing the cotton down but didn’t get it right the first time.

I felt like the vapor and flavor production was very good and liked running the airflow about 1/3 open at 36 watts for a really nice slightly restricted direct lung vape.

I’d like to thank Hellvape and Cara for sending the Hellvape Dead Rabbit R Tank for this review. A big thanks to the readers for sticking it out to the end of my review. Below is a link to the Hellvape website if you would like to explore their line of products.


Dead Rabbit R Tank - Unique Rebuildable Mesh Tank-Hellvape - The DIY atomizer leading brand

Will you be at the VAPE EXPO 2021 in Paris?
We will wait you with arms full of gift for 3 epic days,
Be one of the first 100 to experience our new Target series specially released for launching event.
And more surprises awaiting you!
EXPO Date: 2021.10.16-18
Booth No: B18

Vapefly Kriemhild 80W Kit is composed of Kriemhild 80W Box Mod and Gunther Sub Ohm Tank. One of the innovative features of it is the Security Alarm System contributed by German 103 Team. When the chip detects a risk, the buzzer will send an alert to the user, such as Short Circuit Alarm, Overheat Alarm, 10s Vaping Alarm. Besides, the 3S chip also provides some safety protections: Over-heat Protection, Reversed Battery Connection Protection, Over-current Protection and so on. Kriemhild 80W supports single 18650/20700/21700 battery and comes with Type-C fast charging port. Gunther Sub Ohm Tank is designed with U-shaped top airflow to bring smooth, quiet and leakproof vaping. Compatible with FreeCore K series coils (Kriemhild II Coil) and Kriemhild II RMC, it will provide excellent flavor for you. Gunther Sub Ohm Tank can be refilled by top filling system and hold 3.5ml or 5ml e-juice capacity.




Features:
1. Contains Vapefly Kriemhild 80W Box Mod and Gunther Sub Ohm Tank
2. 80W max output power, Top refilling system
3. Top airflow leak-proof, U shaped airflow
4. Type-C fast charging
5. Compatible with FreeCore K Series Coils(Kriemhild II Coil), Kriemhild II RMC
6. Security alarm system from German 103 Team
7. Short Circuit/Overheat/10s Vaping/ Fully Charged Alarm
8. Compatible with 18650/20700/21700 battery
...

Click here for more:

Kriemhild 80W Kit: Vapefly Kriemhild 80W Kit

Kriemhild 80W Mod: Vapefly Kriemhild 80W Mod

Gunther Top Airflow Tank: Vapefly Gunther Top Airflow Tank

Cyborg Quest 100W Kit contains a Cyborg Quest 100W Box Mod and a 5ml UB Pro Pod Tank. It is created with a spacial-shaped look, which makes it stand out from other vape products. It is not only designed for a vaper, but also a gamer. Powered by Quest 2.0 chip, Cyborg Quest allows you to enjoy fantastic performance. Five vaping modes are available to fit your different vaping needs: Wattage/VPC/Bypass/Voltage/Temperature Control(SS904/SS316/Ti/Ni) mode. Besides, there are also 3 user records. Cyborg Quest Kit can work with single 21700/20700/18650 battery and has 5-100W output power range. The DC 5V Type-C charging design will help you charge the device fast. UB Pro Pod Tank features triple airflow channels and adjustable airflow system. Working with the UB Pro 0.3ohm Mesh Coil, Cyborg Quest will offer accurate temperature control vaping to get brilliant flavor and cloud production. It is compatible with other UB Pro Coil, too.

Lost Vape Cyborg Quest 100W Kit Giveaway, 1 winner, ends on October 26th, 2021

Enter here

So, I just put a Uwell Crown 3 sub-ohm (0.25 SUS316 parallel coil head) on both the Drag X Plus Pro and the OBS Engine and got great performances from both at 80w. The voltage difference is crazy to me though. The DXPP went up to 4.89V (coil reads at 0.3 Ohms) and the OBS Engine rocks the same 80W at about 5.45V (coil reads at 0.28 Ohms). There is definitely some chip wizardry going on here that I'm unaware of or my Engine has been dropped one too many times. Let's do the mathZ.

Both the DXPP and Engine are single 217 boosted mods.

The mathZ: (both mods set to 80W)

DXPP - 4.89 Volts divided by 0.3 Ohms is 16.3 Amps. (Volts / Ohms = Amps)
16.3 Amps times 4.89 Volts = 79.7 Watts. (Amps x Volts = Watts)
--An expected outcome--

OBS Engine - 5.45 Volts divided by 0.28 Ohms is 19.46 Amps. (Volts / Ohms = Amps)
19.46 Amps times 5.45 Volts = 106.1 Watts. (Amps x Volts = Watts)
--Not an expected outcome-- At 80W, the Engine is performing at 106W. In fact, dialing down the mod to 65W is where it performs closely to the DXPP at 80W.

This is both good and bad. We can actually achieve higher performance than we think the Engine is limited to however, it makes the limits at which we push the battery to, guesswork. I just tested 100W on the Engine and the math says it's performing at about 133W. Amp draw is only 21.79 though, so not crazy high. Definitely not dangerous if we are using batteries with >25 Max CDR. However, if someone thinks their mod is drawing 16.3 Amps and is well within the limits of their batteries with 20A Max CDR, then they're going to find themselves with a pretty warm mod and shortened battery lives.

**Another reason to buy batteries with extra Max CDR headroom.**

This mod remains one of my favorites because of its small form factor and wide range in its ability to perform, but I'm starting to wonder if it's because of what is written above. I'm not really bothered by it, but just makes me realize I need to be a little bit more cautious about the readouts. Also another reason I like mods that show Amp load as a readout.

Has anyone else experienced this with their OBS Engine Mods?

The Vapelustion Hannya Nano Pro Pod Kit, a stylish pod kit, works with built-in 700mAh battery with 13.6W output.

Vapelustion Hannya Nano Pro 13.6W Pod Kit has 4 different magnetic art panels and features 2 different airflows.

VAPELUSTION leavea a mark on the list, and NANO has won the reputation For users. VAPELUSTION continues to build momentum and redesign HANNYA NANO PRO, a breakthrough and a tribute. Once again, the infinite possibilities were stimulated, and upgrades were made under the condition of keeping the genes unchanged.

Features:
Material: Zinc Alloy + Plastic
Panel: Metal
Battery: 700mAh built-in battery
Output: 13.6W
Voltage: 3.7V
Capacity: 2ml
Resistance: 0.8ohm cotton coil
Stylish and delicious vape bar
Internal 700mAh battery
Magnetic panel desig
2 different airflow
4 different replacement art panels

More details for Hanny Nano Pro Pod, please check >> https://www.3fvape.com/52674-vapelustion-hannya-nano-pro.html

Let's welcome a new member of Nord family from SMOK - Nord Pro. The last new member is Nord 50W. They have a very similar appearance. You may be curious about the differences between them. Today we are going to have a brief comparison between them.



SMOK Nord Pro
Main Features:
1. Side-filling cartridge, with child-resistant design
2. Compatible with Nord Pro Meshed Coil 0.6/0.9ohm Coils, and also Nord series Coils
3. 1100mAh built-in battery, with intelligent LED indicator, support both button/air activated
4. Adopting in-mould labeling(IML) technique, with prismatic®ular 2 series of shape

Physical Parameter
Size: 96 x 29 x 18.9mm
Capacity: 3.3ml/2ml(TPD/UK)
Resistance: 0.6Ω
Battery: 1100mAh

SMOK Nord 50W
Main Features:
1. Translucent cartridge, side filling system, with two-side adjustable airflow
2. Nord 50W LP2/Nord/RPM Cartridge, compatible with LP2/Nord/RPM series of Coils
3. 1800mAh built-in battery, output power 5-50W
4. Adopting in-mould labeling technique(IML Series) & premium leather pattern(Leather Series)

Physical Parameter:
Size: 31 x 22.6 x 97mm(IML Series) / 32 x 23.9 x 98mm(Leather Series)
Capacity: 4ml/2ml(TPD/UK) (Nord 50W LP2 Pod)
4.5ml/2ml(TPD/UK) (Nord 50W Nord Pod)
Resistance: 0.23/0.6Ω
Battery: 1800mAh

In conclusion, the biggest difference between Nord Pro and Nord 50W is that the Nord Pro is without screen, while the Nord 50W has a OLED screen. Their airflow adjustment method is also different. For Nord Pro, you just need to switch the pod installation direction. For Nord 50W, there is a slide button on the body for all-around airfow. And the Nord Pro supports both button/air activated mode, while the Nord 50W only supports button activated mode.

Besides, the Nord Pro comes with child-resistant design. The safety pod lock uses the ingenious lock design to prevent kids’ access to the pod. What’s more, the Nord Pro is smaller, you can easily put it in your pocket, very convenient to carry.

Learn More:
SMOK Nord Pro
SMOK Nord 50W

ElegoMall provides worldwide shipping and competitive price for all the customers, register on ElegoMall now to get your new user coupon and enjoy better price of more latest vape kits.

Vapx Violet YK6

VapX (Shenzhen) Technology Co., Limited proposes a new entry-level Pod device with pre-filled cartridges, the choice is wide with 15 different flavors at various nicotine concentrations.

Enjoy the reading



► Vapx Violet YK6; Packaging:
The box packaging is extremely simple and shows many small blue Vapx logos on the front on a white background, the name and the brand written in black.



Inside we find only the device and the user manual, without the cartridge and without the charging cable and this surprised me enough. I thought the cartridges will be sent to me later and they did.



► Vapx Violet YK6; Preloaded cartridges:
A few days after receiving the Pod device, the courier handed me the cartridges with so many different flavors, I was impressed with this great variety. Each box contains a coil and three refills, the package shows the taste, capacity (1.7ml) and nicotine concentration on a label.





► Vapx Violet YK6; Available flavors:
• 4 "Mix" available; Strawberry Kiwi, Pineapple Coconut, Aloe Grape, Mixed Berry
• 11 "Original Flavor" available; Ice Orange, Ice Mojito, Ice watermelon, Ice Grape, Ice Lychee, Ice Americano, Ice Apple, Ice Guava, Sweet Mint, Ice Lime, Caramel Tobacco.
* Ice Grape not received



► Vapx Violet YK6; Product Specifications:
• YK6 Pod Device Size: 87 * 19.6 * 10.5mm
• 7W output power
• 350mAh battery
• Charging current 400mA
• Type of charge Tpe-C
• Charging time 75 minutes



► Vapx Violet YK6; Available colours:
• Cosmo Violet, Wonder-land, Gunmetal Gray, Tempest Blue, Space Odyssey.



► Vapx Violet YK6; First impressions:
I have no news on how the final version of Violet YK6 will be packaged, what I have received are two packs; the first pack contained the device without the included cartridges, the second pack arrived a few days later and contained a large amount of pre-filled flavored cartridges.

YK6 is an extremely handy device with a flattened oval shape very small in size and also appears quite sturdy being built in aluminum.



► Vapx Violet YK6; 360 ° view:
On what I define the main side there is a LED that lights up every time the device is activated, this LED also takes care of sending notifications to the user regarding the safety protections. At the bottom there is a small symbol and no other brand. On both sides of the YK6 there is a small hole for the airflow.

Vapefly Kriemhild 80W Box Mod Kit is composed of Kriemhild 80W Box Mod and Gunther Sub Ohm Tank.


The Vapefly kriemhild 80W Mod is one of the innovative features of it is the Security Alarm System contributed by German 103 Team. When the chip detects a risk, the buzzer will send an alert to the user, such as Short Circuit Alarm, Overheat Alarm, 10s Vaping Alarm. Besides, the 3S chip also provides some safety protections: Over-heat Protection, Reversed Battery Connection Protection, Over-current Protection and so on. Kriemhild 80W supports single 18650 / 20700 / 21700 battery and comes with Type-C fast charging port.


Vapefly Gunther Sub Ohm Tank is designed with U-shaped top airflow to bring smooth, quiet and leakproof vaping. Compatible with FreeCore? K series coils (Kriemhild II Coil) and Kriemhild II RMC, it will provide excellent flavor for you. Gunther Sub Ohm Tank can be refilled by top filling system and hold 3.5ml or 5ml e-juice capacity.


Featurs of Vapefly Kriemhild 80W Box Mod:
510 threading connection
Mod Size: 87.5 x 43.7 x 30.0mm
Battery Type: Single 18650 / 20700 / 21700 (not included)
Output Voltage: 0.5~8V
Power Range: 5~80W
Output Mode: VW / Bypass
Coil Resistance: 0.1~3.5ohm
Screen: 0.49 inch OLED
Type-C fast charging
Short Circuit / Overheat / 10s Vaping / Fully Charged Alarm
Compatible with 18650 / 20700 / 21700 battery (not included)
3S chip protections: Short Circuit / Over Charge / 10s Cut-off / Over-heat / Reversed Battery Connection / Over-current Protection.


Features of Vapefly Gunther Sub Ohm Tank:
510 threading connection
Size: 25.2 x 54.5mm
Capacity: 3.5ml / 5ml (with bubble glass)
Drip Tip 810 (510 adapter included)
Coil: FreeCore? Duplex? Mesh Coil:0.2ohm, FreeCore? Mesh Coil 0.3ohm, Kriemhild II RMC
Filling Type: Top filling system
Approved by German 103 Team
Top refilling system
Top airflow leak-proof, U shaped airflow
5ml / 3.5ml e-juice capacity
Compatible with FreeCore? K Series Coils (Kriemhild II Coil), Kriemhild II RMC


More details for Vapefly Kriemhild 80W Box Mod + Gunther Sub Ohm Tank Kit, please check >> https://www.3fvape.com/52778-vapefly-kriemhild-80wbox-mod-gunther-sub-ohm-tank-kit.html


Quick links to the mod and tank as below


Kriemhild 80W Mod >> https://www.3fvape.com/52785-vapefly-kriemhild-80w-box-mod.html


Vapefly Gunthere Tank >> https://www.3fvape.com/52777-vapefly-gunther-sub-ohm-tank.html

Marvos RTA Pod by Freemax is compatible with both replaceable mesh coil and DIY wires, you can choose one of them to build on the deck according to your preferences. The deck has a clamp on each side that is secured with screws and a spring-loaded ceramic block to support the cotton, ensuring that the cotton is in full contact with the mesh coil.



If you get one Marvos RTA Pod, you will also get these accessories below. So what are in the box package?
Marvos RTA Pod 2mL x 1
Accessories Bag x 1 (Containing the following parts)
-0.15ohm Mesh Coil x 1 (60W Max）
-0.2ohm Mesh Coil x 1 (40W Max)
-Sealing Ring x 2
-Bending Tool x 1
-Screwdriver x 1
-Phillips Head Screw x 2
Cotton x 1
User Manual x 1
Desiccant x 1

Hi all,

I am a former smoker of 15+ years. I quit successfully like many others by switching completely to vaping. I dabbled in vaping a few years prior to making the full switch, but due to the learning curve, user error, and nicotine laws in my country, I didn't fully commit to it and eventually went back to smoking.

I have now fully embraced vaping as a smoking cessation tool, and have found a new passion in this industry. From starting with a dual 18650 regulated box mod with stock sub-ohm coil tanks, I have now shifted exclusively to rebuildables and most recently mech mods.

Hoping to contribute and ask questions on this forum as much as possible.