Indulgence Mt-Rta
- Thread starter 98ruby
- Start date
- th_trl_thread_readers 0
- Status
I posed that question before mine came in. I love mine! Welcome to the thread, it's nice in here.
Didn't even think about closing AFC on a topfill. Used to my Subtank mini which I still love just not as much as this awesome thing! Still looking for advice on a good temp control build.I've decided its trustworthy and am running regulated now. No hints of a gurgle at all. I have two suggestions on your build:
1. Long enough coil to span the entire length of the airhole. That way your wick won't be dribbling any juice down the airhole.
2. Cut your wick tails all the way to the bottoms of the channels and shove the whole thing in
Typical top filling:
1. Close afc
2. Fill with needle bottle so air can escape also since it only has one hole for both filling and air displacement.
3. Screw on top cap and flip as you do that last half turn in a continuous motion
4. Open afc while inverted.
Yep, figured that out nothing but bent coils. How about titanium or stainless?
I dunno if its necessary on this one, BUT I forgot once on my Aga t7 and accidentally opened it back up on my HC Plus and freaking flood city
So now I pretty much always do. My Eviva t, however, does fine leaving the afc open.
Wick it like normal in the coil, not to tight but not pull right thru loose. I put a gang load of cotton in the wicking channels and it worked great
Haley, I have a 24ga spaced Ti build in mine right now. 2.5mm with 6 wraps is giving me .21 ohms running at 390 joules. Damn fine vape, although Noodle had to point me in the right direction for stuffing those channels with cotton.
I get my TI here:
http://www.riogrande.com/Product/Titanium-Round-Wire,-50_dash_ft-Coil,-24_dash_Ga,-Soft/135503
Glad to hear you got it up and running. I haven't had to re wick yet but its coming soon. I've been thru 90ml since I wicked it, if won't be much longer
Sent from my Nexus 6 using Tapatalk
I haven't felt the need to rewick yet. This thing just keeps on pumping without inconsistencies so, I'll leave it. I am going to switch over to a dual 26ga though. 24 takes a bit to get going for my likes.
I EFFING LOVE THIS TANK!!! WOOOOOO!!!
I EFFING LOVE THIS TANK!!! WOOOOOO!!!
I'm running .3 ohm Clapton coils. 26g core with 32g wrapped around it 5 wraps on a 3mm bit.
I get the (funny bubbles) lol from 2 holes but one of them really pumps them out and the other barely makes any. I dont get any dry hits and don't flood out tho
Sent from my Nexus 6 using Tapatalk
I am glad I read your post. I get bubbles from only one juice channel, too. I guess that's normal.
From checking out other wicking tips on the web I have found one that seams to help prevent flooding. Wick as usual, screw the chimney on with wick sticking out of the juice channels, stuff some wick in to the juice channel, and trim the wick so that maybe 1-2 mm is still sticking out of the juice channel opening. Do this rather than shoving all the wick in to the juice channel opening. I have a build like this I did last night, and not a drip has trickled down the airflow.
One more thing. The AFC ring isn't exactly air tight when closed, so when filling I hold my thumb and forefinger over the air flow holes and this creates an air tight seal.
One more thing. The AFC ring isn't exactly air tight when closed, so when filling I hold my thumb and forefinger over the air flow holes and this creates an air tight seal.
- Status
