been gone for a while , still a vaper since 2010, and i used to participate in the
modding forum.
i stopped in to modding forum and just about all threads are locked,
is it allowed ? or just no interest in modding ?
Hi all i did another thread on this a couple of years back .
It was a mod i made to a deck on a Steamcrave Aromamizer
This mod can be Done on most Velocity style decks
the old thread was called " Aromamizer single coil with a twist "
The velocity deck in this atty and most other...
Hi I just got my AL85 boxmod and I was wondering if there are any configurations that I can do with it? such as plug it into the computer and mess around with settings or something such? modding the display or whatever. Thanks :)
Want to vape without Fire press button and it can be realized in FW
One of option: somthing should be connected to +- column. If you dont inhale, something shorter (not 0.00 short circuit, but it should decrease resistance). If you inhale, it should open.
In this case, firmware can use sharp...
I am looking at Alpinetech boxes P+, B and G+ for a DNA200 3S LiPo build and was wondering if anyone else has build on any of these box sizes and if so, what were the best (ie highest watt hours) 3S LiPo packs that could be fit into any of these box sizes.
Hope the question makes sense, thanks!
So i have this Hana DNA30 v3 clone from FT, never had a problem with it. Used it around 7 months now.
But the fire button just popped loose from the case and is damaged.
Im good at doing, i just need the electrical advise. I want to replace the tiny dome tact switch with a 12-16mm blue LED...
Is it possible to use parts from a ITaste VV/VW V3. I am not shy to re-soldering and making a new box. I believe its possible I just need some advice. Maybe if I do this I will go on to bigger and better things
Really new to all this and just want to get a grasp on things. What is the point of insanely high watt box mods? I heard that the higher wattage the better? But then I just saw on here that it just is a miserable vaping experience to vape at abnormally high watts. I'm lost here and I just need...
Looking to make my first VV box mod, I want it to be 100+ Watts. Ability to sub ohm. 2 good batteries (maybe 18650 or 14500s?). A USB charging port? LED display. Push button voltage adjusters instead of the twist thing. Looking into the Raptor 20A but still don't even know where to start. i'm...
Alright so I bought a TOBH for the sole purpose of cloud chasing with it. Now so far , I've absolutely love it. Hits well , and the stock airflow isn't too bad. I put some 22g .13ohm dual micro coils on it. Which it isn't going to bad , but for clouds my .36 26g nano's on my Trident is beating...
I'm not sure if this is the right section to post under, but since it would involve modding a battery, it was my best guess.. I'm wondering if it is possible to paint, or other-wise recolor batteries, particularly 18650's. I have a sweet AR mod on the way, and it has large holes on every side of...
Okay, so this feels really weird, but I have been vaping for like 2 years and I barely ask advice anymore, but I have never made my own mod! My goal in all this is to eventually build a dual 26650 mechanical (Box mod and a tube... Because I can... lol). I know. Lofty goals. I was thinking of...
The center pin fell out of my 510 connector! I found the pin after looking around for a while, but have no idea how to secure it in the 510 again. Has anyone else had this problem? Any ideas on how to repair it? Any feedback would be much appreciated! Thanks in advance!
Ok. So my first mod has officially been built! Technically its my second, because I hooked a 510 up to a battery box to run it off AAs a couple weeks ago, but this is my first full build. My idea was very similar to the Fog Log which I've seen posted about on these forums. I hadn't heard of said...
Hey all, if anyone has modded there atomizer systems, slap some photos and some info up. Share the wealth.
Modded RSST dual wick hole dual neg posts threaded stock fill hole cap drilled out and dual airflow
I love my KFL+ as well as the SQuape, they have many similarities, including draw. I don't find the airflow control on the kfl+ opens up as far as I'd like.
Today I drilled out my SQuape to 1/16" and it is now just perfect. Would really like to find a way to do this to the KFL+. Subscribed to...
I just purchased a copper Vanilla mod made by Smok-E Mountain today and I already want to mod it even before it gets here (wouldn't you be excited too?) Anyway I'm curious if there's any easy way to do this like you can a Nemesis. Or better yet, can I just use the magnets that you can buy from...
purchased on impulse about an hour ago because of the 19mm od, and threaded top cap... looking at the pictures there is no visible air hole on the top cap. the base must be vented, i'll definitely plug that hole and drill a new hole at coil height... maybe tap threads into the hole and thread a...
I saw a YouTube video on this the other day. I was making a mesh wick for my Z Atty Pro yesterday so I could compare it to the ceramic ones I have been using in it. Ended up with a small piece left over after I trimmed it to fit the Z atty. Sooooooo....... What the heck I pulled apart an old...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.