Nemesis Mod Question

Discussion in 'General Vaping Discussion' started by nikkysikk, Mar 7, 2014.

Thread Status:
Not open for further replies.
Image has been removed.
URL has been removed.
Email address has been removed.
Media has been removed.
  1. nikkysikk

    nikkysikk Moved On ECF Veteran

    Joined:
    Apr 14, 2013
    Location:
    Michigan
    I purchased a Nemesis Clone today and it was having some trouble making contact. My friend started to take it apart and a small metal cylinder about half an inch or less long came out. What is this for? It was rattling around and fell out when the bottom was unscrewed.
     
  2. Top_Bunk

    Top_Bunk Full Member Verified Member

    Joined:
    Nov 3, 2013
    Location:
    Cbus!
    You're not talking about the locking ring, are you?
     
  3. CShaver

    CShaver Super Member Verified Member ECF Veteran

    Supporting member
    Joined:
    Jan 3, 2014
    Location:
    Swoyersville, PA
    That needs to be in the hole between the contact and the part it's screwed into.

    Also, if you're not using a kick, take the middle ring out or it won't make contact. At least it didn't for me.

    I'll edit the post in a minute to get pics lmao

    Here's what I meant.
    Screenshot_2014-03-06-21-14-11.jpg

    And here's a pic with the middle ring out.
    Screenshot_2014-03-06-21-14-31.jpg
     
  4. crxess

    crxess ECF Guru Verified Member ECF Veteran

    Joined:
    Sep 20, 2012
    Location:
    Williamsport Md
    Small pin, size of rice.
    Remove silver contact pin in switch while holding bottom and Black Delron together.(Otherwise switch will fly apart)
    See groove cut in center post side and Brass threaded section.
    Aline Grooves and insert Rice Pin
    Install silver contact screw
    Done.
     
  5. Top_Bunk

    Top_Bunk Full Member Verified Member

    Joined:
    Nov 3, 2013
    Location:
    Cbus!
    Ahhh yes I forgot about that part. I ended up wrenching down my switch so it wouldn't pop again.
     
  6. nikkysikk

    nikkysikk Moved On ECF Veteran

    Joined:
    Apr 14, 2013
    Location:
    Michigan
    What causes only one tank to work? I can only get my rsst to fire nothing else works on my nemesis.


    Sent from my iPhone using magic.
     
  7. joecil

    joecil Super Member Verified Member ECF Veteran

    Joined:
    Jan 9, 2014
    Location:
    Russell Springs, Kentucky
    I am wondering when you put on the atty are you adjusting the top pin to meet it? If so you can pretty much use any 510 atty on it that I've seen. I run Kayfun, Aspire (several different types), Protanks, Davide, IGO etc none have not made contact when the pin is adjusted to it. As for the rest remove the small ring on the tube unless you are using a fuse or Kick. Now if that doesn't work or you want to use the beauty/kick ring then get the FatDaddy replacement top and button pins so it can be used regardless.
     
  8. crxess

    crxess ECF Guru Verified Member ECF Veteran

    Joined:
    Sep 20, 2012
    Location:
    Williamsport Md
    Lack of knowledge!

    Nemesis center pin is adjustable.
    Remove Nemesis top
    Back off center pin with thumbscrew knob
    Attach any Device
    Snug Thumbscrew
    Install Top Cap
    Adjust bottom switch as needed

    Vape On! :vapor:
     
  9. scylla

    scylla Senior Member Verified Member ECF Veteran

    Joined:
    Jan 21, 2010
    Location:
    Illinois
    This.

    Put your tank on first, then tighten the pin.
     
  10. nikkysikk

    nikkysikk Moved On ECF Veteran

    Joined:
    Apr 14, 2013
    Location:
    Michigan
    I have done this but none of my tanks are working still


    Sent from my iPhone using magic.
     
  11. joecil

    joecil Super Member Verified Member ECF Veteran

    Joined:
    Jan 9, 2014
    Location:
    Russell Springs, Kentucky
    If that is the case check first the ohms on the atty to make sure it isn't shorted or the coil is bad. One other thing is also if it is a short there is a chance you burned an insulator in it also. Now if that doesn't work they next thing is the battery you are using or the APV. Nothing short of replacing will do much.
     
  12. Vermonster13

    Vermonster13 Vaping Master Verified Member ECF Veteran

    Joined:
    Sep 13, 2010
    Location:
    Rutland, Vermont
    Watching a few of the Nemesis videos on assembly/adjustment/disassembling is highly suggested.
     
: problem, mod, nemesis
Thread Status:
Not open for further replies.

Share This Page