AFS feedbacks
- Thread starter imeothanasis
- Start date
- th_trl_thread_readers 0
- Status
I think this is my problem.....I find it very difficult to press the button in this position. I tried unscrewing the end cap to bring it to 12 on turn it upside down use the button on the bottom but I found this just as hard to use....me and my fingers...
I don't like those ones so I chucked most of the ones I had - I hope I can find a few arond here somewhere.
Does using your other hand help at all?I think this is my problem.....I find it very difficult to press the button in this position. I tried unscrewing the end cap to bring it to 12 on turn it upside down use the button on the bottom but I found this just as hard to use....me and my fingers...
You just gave me an idea... You could try some different magnet spacers to get the cap to screw in the right stopping point... Thanks I will try and report back...
That works... THANK YOU for the idea... I am not sure it will work for you guys with the Trans or not... I have these 1mm spacers I got for the Slim batts... I added one and it put the atty hole at about 7 oclock... good enough... Problem solved... see why I love this Forum..
That works... THANK YOU for the idea... I am not sure it will work for you guys with the Trans or not... I have these 1mm spacers I got for the Slim batts... I added one and it put the atty hole at about 7 oclock... good enough... Problem solved... see why I love this Forum..
Last edited:
Using my trans in the Grant...I can get button on top and hole at 5 o'clock which would be fine...except I have no batteries for the 3.7v....But at least I've got somewhere today, tomorrow I will try the AFS using 2 hands with the 18650 mode to see if I can get it working.....thanks guy and gal...
Hi,Ladies and gentlemen
My AFS operates well now.
Well, I am testing the capacity of AFS of the maximum liquid.
When the injection syringe was used and tested, the conclusion that the liquid of 3 to 3.5ml or less was able to be filled to AFS was obtained.
Should I fill it fewer?
Thanks
My AFS operates well now.
Well, I am testing the capacity of AFS of the maximum liquid.
When the injection syringe was used and tested, the conclusion that the liquid of 3 to 3.5ml or less was able to be filled to AFS was obtained.
Should I fill it fewer?
Thanks
Been using the AFS for about 8hrs now, i must say i'm very impressed, only been using it at 6v and the vapour is amazing, throat hit is excellent (not quite as good as a 501, but that's apples and oranges) and the taste is indeed retained a lot better, i was sceptical about that claim.
however a couple of things i have noted, mine leaks a little bit from the bottom, i'm assuming its just a slightly faulty "O" ring so that can be rectified quite easily, and one thing to note is the slightest knock will shift it out of position, these are small quibbles i know but i thought i would point them out.
The AFS lasted me 1hour and 45mins before it needed topping up, i did nothing apart from re prime the atomizer by drawing on it without pressing the button a couple of times, outstanding really.
If this was made completely leak proof and was held more rigidly in place on the atty it would be close to a perfect product.
This may read like a slightly negative review but it is far from it, its an excellent device, i'm loving it and would recommend anybody to buy it straight away upon release
could you tell me the diameter of the o rings you used for the AFS please imeo? i want to replace the bottom one and just have a couple of spares.
p.s the all brass GGslim i received far exceeded my expectations, its beautiful and the perfect pocket pv
negative post?? I see it like one of the best posts womb!! Thanks a lot my friend about your points for AFS, I need them to make it even better.
The o-ring internal diameter is 9 mm and the width of o-ring is 1,5mm
And thanks because you are pleased with the Slim womb. I am really happy
The atty hole is at 2'oclock...if I move it up or down then the button is really quite difficult for me to press...if I turn the atty to 12 o'clock then it is far too loose and falls off....
I vape at 10 degrees..
I use 2 drops withe 3'7v...
The atty isn't broken because it still lights up when button is pressed...its more likely I'm using it wrong.....
maybe my hole isnt open enough. Did you used a thick liquid moog? Maybe your inhales are not as hard as AFS requires. I made it for me, so if more people have trouble with it, I will open the hole a little more, thats very easy for any new atty
Another reason to love the AFS, if you like to mix your own liquids like I do, then its pretty simple, 1. add unflavored juice 2. add flavoring. Shake it up and vape. So far I've had no leaks. I have however had problems with VG juice, so the hole mad on the atomizer needs to be a little larger, but it works fine with PG based juice because its not as thick. mmmmm mmmmmm the juicey fruit flavor tastes fantastic in this
maybe my hole isnt open enough. Did you used a thick liquid moog? Maybe your inhales are not as hard as AFS requires. I made it for me, so if more people have trouble with it, I will open the hole a little more, thats very easy for any new atty
Yes, I would suggest that you make the hole a tiny bit bigger based on feedbacks you've had here and from what people have said to me also.
We probably all took much harder draws when we smoked analogs, and then got used to a slighly longer but less strong draw when we converted to e-cigs. Going back to very hard drawing again is another unecessary change perhaps?
From my point of view - and maybe a lot of the other ladies (dunno about the men) it's better to take a slightly less hard draw as the more you contort your face to draw, the more likely you are to get increased smoker's lines and wrinkles in the skin around your mouth and lips......(another reason why flat mouthpieces are also better than round ones).
Didn't think of this - this has got to be a fantastic benefit, particularly for a juice-chef such as yourself Crash.
- Status
