Hi, I just recently began vaping, and I have an iTaste vv3 with iClear16s. I got my mountbakervapor order today and tried some of the juices. Cinnamon roll and orange dream bar seem to get a burnt flavor and im not getting much of the cinnamon/orange flavor. I have it set at 8 watts/4 volts. Anythng I might be doing wrong? Any help is appreciated thanks
Am I doing something wrong?
- Thread starter Dlj272727
- Start date
- th_trl_thread_readers 0
- Status
Oh my I don't think you're supposed to use those flavors in those tanks 
That wouldn't cause them to not work though, just crack the clearo. What's your voltage set at?
That wouldn't cause them to not work though, just crack the clearo. What's your voltage set at?
In all likelihood, you need to let the liquids steep for at least a few days. Are you familiar with steeping?
Edited to add: Rose is correct, too! Both of those liquids are "tank crackers" and should only be used in glass/pyrex tanks. You may be getting funky chemical taste from the damage the liquid is doing to the tank.
Edited to add: Rose is correct, too! Both of those liquids are "tank crackers" and should only be used in glass/pyrex tanks. You may be getting funky chemical taste from the damage the liquid is doing to the tank.
Try going down to 6 - 7 watts. if that doesn't work. your juices might need to steep?
oh dear forgot about the satan juices. that could be your problem if the tank is plastic... make sure your tank isn't fogging up or looking a little melty.
Coils be plastic from the tank reacting from the liquid, and it's affecting the vape? IClear 16’s are FFS for flavor usually. Also, I recommend to steep all mtbaker liquids. They're good, but they need time to settle wwhen they arrive.
I'd try backing down the watts to 6.5 and then to 7, 7.5 and see if you get a better taste in those ranges. I vape with the iTaste vv v3 too and I rarely find a juice that needs to be vaped at 8+. What is your coil ohms reading?.
Here's a chart that tells you w/v settings according to your coil ohms number.http://www.ecigadvanced.com/community/wp-content/uploads/2012/07/power.jpg
Here's a chart that tells you w/v settings according to your coil ohms number.http://www.ecigadvanced.com/community/wp-content/uploads/2012/07/power.jpg
Last edited:
Some tanks I buy taste like plastic unless I clean them. Some are fine the moment they arrive from the store and some just taste awful. Maybe do a clean in 80% rubbing alchol. I know you need to search them out to find them that high. Your other option is to use everclear and clean them that way. Basically removing any mechanical type oils that are left over in the manufacturing type process. Surprisingly I have some that need no cleaning and some that I can't stand withouhout cleaning...same vendor.
What's the ratio you're using? When I first started DIY, I was mixing at 30/70 PG/VG and learned the hard way that some juices weren't wicking well enough in my iClear's, resulting in some pretty terrible flavor. I didn't realize how good my RY4 should have been tasting until I got my dripper and tried it in that. I was blown away by how much better the flavor was for all my high VG juices.
Thanks for all the input guys! Alot of people have said cinnamon roll is great out of the box so I didnt think it would need steeping but im steeping all my juices now. I think the burnt flavor is coming from me using a plastic tank so im planning on getting a protank or something
What blend did you order though? I'm telling you from experience I wouldn't try to put anything thicker than 65/30 PG/VG through an iClear. It really altered the flavor of a lot of juices that I was using at 40/60 or higher VG by producing dry hits since it couldn't wick fast enough.
All of my juices are 65/30 or 80/20, none are thicker than that
- Status
Similar threads
