Aromamizer RDTA by Steam Crave
- Thread starter roxynoodle
- Start date
- th_trl_thread_readers 0
- Status
When mine is on too tight I use the little chimney tube to unscrew it. Hopefully that works for you too.
Let us know how they compare to each other please!Thing is, when an electrical connection isn't tight what does it do? Think welding, while it may work, any time you have a connection that carries any sort of current and it is loose that is not a good thing.
Will it cause any real issues? Probably not, but the possibility exists. I would agree, move the tank, not the deck. After all the raving about this atomizer, I finally broke down, and should have mine Friday along with a Crius. Going to line them up with my Bellus, and Indulgence, and see which one I prefer.
Hey Roxy, I've been prepping for dark days ahead also
Where the grub screw goes to hold the coil leg, they were originally drilling/tapping that all the way through the post, so that there was a hole on the inside of the post. Now, like the original Velocity, they only drill through one side so when you tighten the grub screw, it pins the coil leg against the back of the post.
Edit: ismokeinbinary beat me to it!
24ga nich 80.....2.5mm.....10 wraps...... .28ohms
drillbit......Ive been vaping all day at 100 watts and its pretty juicy.......
at the higher test wattage its not dry but definitely not juicy....
While not quite sure about the question the 3 and 6 ml both use the same glass piece. Kayfun v4 gass tank sections also fit.
I mean how does that make it a 3ml? Doesn't the 3ml have a smaller glass tube part? Wouldn't I need to buy an extra glass in a 3ml size?
nope, same size glass only the chimney is different size
hi all !
just got 1 gal of vg and another gal of pg ..also 240 ml of 100 mg nick ..how you guys preserve it long time??
will this freeze solid in a freezer ? any other ideas /.
vaping on two different builds in the aromamiser since I had 34 kanthal for claptons and did not like them dicided to twist 4 strands . on 2.5 mm
was 1.8 ohms. my favored till now.
the last build is 18 g wire wound parallel on 3 mm form . 5 wraps ..so 10 wires side by side . two end to pos the other two ends to neg.
like a duel coil in one micro coil. came out to 0.66 ohm ! lower then all my others.
very smooth full bodied flavor ..at 22 watts.love it!
just got 1 gal of vg and another gal of pg ..also 240 ml of 100 mg nick ..how you guys preserve it long time??
will this freeze solid in a freezer ? any other ideas /.
vaping on two different builds in the aromamiser since I had 34 kanthal for claptons and did not like them dicided to twist 4 strands . on 2.5 mm
was 1.8 ohms. my favored till now.
the last build is 18 g wire wound parallel on 3 mm form . 5 wraps ..so 10 wires side by side . two end to pos the other two ends to neg.
like a duel coil in one micro coil. came out to 0.66 ohm ! lower then all my others.
very smooth full bodied flavor ..at 22 watts.love it!
I break my nic into 60ml blue bottles and freeze. Leave as little air in the bottle as possible as air oxidizes nic. It does not freeze solid. It freezes into a thick state and I just remove and let thaw to room temp and refreeze what I don't use. Happy mixing.
I see focalecig is now selling clones of the aromamizer rdta it was bound to happen
thanks wharfrat !
so all you freeze is the nick base ? pg and vg should be ok as is ?
just notised on my last build....the wire is not 18 !typo ..it is 28 gage sorry.
- Status
