Here we have another great titanium 22mm rebuildable tank atomizer with Adjustable Air Control and adjustable Postive Post.
Shown with optional all Ti tank and Ti Cubuc drip ti
The great part about it is - It can be used with 3 different setup modes - this should appeal to all vapers since they can have a different vape when wanted.
First as a 3ml tank utiiizing an internal bell. It comes installed with a wick and coil - and the 2 pieces of mesh that feed the wick. Two holes in the bottom of the bell allows the juice through to the mesh. Air to the coil come from Bashiks well known classic center air post.
The air is adjusted with a 1.5mm allen wrench on the outer base of the atomizer. This allows you to adjust the air without removing the atomizer from the PV. I applaud Bashik for doing this, much easier now with this placement. AIR ADJUSTMENT sizes are 0 mm to 1.6 mm
He has also mastered the sound of air when inhaling. Some people had mentioned this with previous atomizers - now there is no sound.
The atomizer is filled from the top. It has two holes available to fill from, then is closed off for no leaking. A brilliant design. No need to remove atomizer from the PV.
Shown here with pima cotton wick fed by mesh.
The atty works well like this - or the mesh tubes can be replaced using tails from a cotton or silica wick and fed through the holes instead
If you like the flavor of mesh - it also can be used with a Mesh U-wick as pictured here
Second - it can be used as a straight dripper. The drip mode piece is included. To me this is where this atomizer shines. It has spectacular flavor in this mode. You can lay it down and it will not leak.. The only dripper better than this - is the Achilles and only by a little bit as far as flavor and ease of setup
shown here with drip mode piece that fits inside top cap - the two small holes you see on the sides are the juice fill holes.
Here in drip mode using all Pima Cotton - I prefer this way the best for my taste
Third mode - is Filler mode - yes you can fit a small amount of filler into the top around the drip mode piece. Then it can be used like a smaller version of Prometey 2. If there is a way to make a filler atomizer - I will do it.
Shown here with filler around drip piece
On the Ti Coated Caravela
Again an atomizer that can be used with three different modes. I recommend this with no hesitation.
Technical data:
a fully mechanical, without wires and soldering.
+ adjustable airflow
+ airflow control
+ adjustable positive pin.
+ full compatibility with battery mods.
+ easy filling through the top cover
+ works with all types of wicks (mesh,silica thread)
Material: titanium.
Diameter:22 mm.
Height (without connector and drip tip): 48 mm.
visually perceived part - 41 mm.
the volume - 3 ml.
Weight: 33 gr
«ATAMAN» set:
- atomizer «ATAMAN» [FULL titanium] - 1 piece
- allen key to adjust the air hole - 1 piece
- thread of silica -1 meter
- nichrome wire 0.20 mm-1 meter
- piece of mesh to wick feed - 1 piece
- plastic drip tip - 1 piece
It will look like this when you receive it - the Smoking Man will be engraved on it now.
Price is 125 euros INCLUDING worldwide Registered Shipping
http://titanium-mods.com/home/46-ataman-full-titanium.html
If you wish for a full titanium Ataman with no clear window - an extra all metal tank is available for 25 euros in the accessory section of site.
DRIP MODE Piece is New Addition He will have them available on website in a week or so for those who want one.
Price will be 10 euros plus shipping - for those who already have an Ataman. No shipping charge if ordered with an Ataman
Pictures:::
Shown with optional all Ti tank and Ti Cubuc drip ti
The great part about it is - It can be used with 3 different setup modes - this should appeal to all vapers since they can have a different vape when wanted.
First as a 3ml tank utiiizing an internal bell. It comes installed with a wick and coil - and the 2 pieces of mesh that feed the wick. Two holes in the bottom of the bell allows the juice through to the mesh. Air to the coil come from Bashiks well known classic center air post.
The air is adjusted with a 1.5mm allen wrench on the outer base of the atomizer. This allows you to adjust the air without removing the atomizer from the PV. I applaud Bashik for doing this, much easier now with this placement. AIR ADJUSTMENT sizes are 0 mm to 1.6 mm
He has also mastered the sound of air when inhaling. Some people had mentioned this with previous atomizers - now there is no sound.
The atomizer is filled from the top. It has two holes available to fill from, then is closed off for no leaking. A brilliant design. No need to remove atomizer from the PV.
Shown here with pima cotton wick fed by mesh.
The atty works well like this - or the mesh tubes can be replaced using tails from a cotton or silica wick and fed through the holes instead
If you like the flavor of mesh - it also can be used with a Mesh U-wick as pictured here
Second - it can be used as a straight dripper. The drip mode piece is included. To me this is where this atomizer shines. It has spectacular flavor in this mode. You can lay it down and it will not leak.. The only dripper better than this - is the Achilles and only by a little bit as far as flavor and ease of setup
shown here with drip mode piece that fits inside top cap - the two small holes you see on the sides are the juice fill holes.
Here in drip mode using all Pima Cotton - I prefer this way the best for my taste
Third mode - is Filler mode - yes you can fit a small amount of filler into the top around the drip mode piece. Then it can be used like a smaller version of Prometey 2. If there is a way to make a filler atomizer - I will do it.
Shown here with filler around drip piece
On the Ti Coated Caravela
Again an atomizer that can be used with three different modes. I recommend this with no hesitation.
Technical data:
a fully mechanical, without wires and soldering.
+ adjustable airflow
+ airflow control
+ adjustable positive pin.
+ full compatibility with battery mods.
+ easy filling through the top cover
+ works with all types of wicks (mesh,silica thread)
Material: titanium.
Diameter:22 mm.
Height (without connector and drip tip): 48 mm.
visually perceived part - 41 mm.
the volume - 3 ml.
Weight: 33 gr
«ATAMAN» set:
- atomizer «ATAMAN» [FULL titanium] - 1 piece
- allen key to adjust the air hole - 1 piece
- thread of silica -1 meter
- nichrome wire 0.20 mm-1 meter
- piece of mesh to wick feed - 1 piece
- plastic drip tip - 1 piece
It will look like this when you receive it - the Smoking Man will be engraved on it now.
Price is 125 euros INCLUDING worldwide Registered Shipping
http://titanium-mods.com/home/46-ataman-full-titanium.html
If you wish for a full titanium Ataman with no clear window - an extra all metal tank is available for 25 euros in the accessory section of site.
DRIP MODE Piece is New Addition He will have them available on website in a week or so for those who want one.
Price will be 10 euros plus shipping - for those who already have an Ataman. No shipping charge if ordered with an Ataman
Pictures:::
Last edited:
