Atmistique Atomizers

[Kataphraktos]

I know, they look pretty sweet. Would look even better if you were able to slide the lid open, and see a v2 diver with one of cool new tubes inside.

Especially since the BB tank itself is a work of art as well.

 

[Konstantinos]

As i mentioned before the CE2 ceramics has very big tolerance. If you have a small diameter ceramic put double the edge of negative to base/ceramic or as finagle do right you can make a loop around the ceramic

From Monday we will receive at many times Divers parts and i hope very soon we can offer very soon separately tubes

 

[Gunslinger317]

As i mentioned before the CE2 ceramics has very big tolerance. If you have a small diameter ceramic put double the edge of negative to base/ceramic or as finagle do right you can make a loop around the ceramic

From Monday we will receive at many times Divers parts and i hope very soon we can offer very soon separately tubes

2864 can't find tracking for.

 

[qorax]

IT IS OFFICIAL : Diver v2 = NO LEAKAGE√

Kept it unvaped for 24 hrs. tank fully topped-up. Checked in the morning... Not a single drop anywhere
Everything is bone dry! The 510 bottom of the Diver, as well as the top-cap of the mod... "0" moistness.
This is it√ Done Deal.

 

[qorax]

 

[Konstantinos]

These o-rings do great job for sealing Q.
I was ready to suggest put your Scuba brass ring but i see the Enezlis tube

 

[Konstantinos]

2864 can't find tracking for.

21/11/13 you must already received from Paypal an email with your track number.
Beginning of this week you must receive your order

 

[Gunslinger317]

Thanks. Hope it comes Monday!

 

[raqball]

Thanks. Hope it comes Monday!

Take that tracking number and put it into the USPS website.. It will track via USPS

 

[Gunslinger317]

Just says it's been shipped

 

[raqball]

I just looked at your tracking on the USPS website ( I hope you don't mind )

 

[Kataphraktos]

Just says it's been shipped

This means it hasn't arrived on US shores. It will update when it is scanned by USPS.

Edit: As per raqball's post, it just hit US shores!

 

[Kataphraktos]

I have now converted my three tank Divers (not the Grail Diver) from the lower acetal to the 4 o-rings. I built microcoils between 1.3 and 1.5 ohms in all three. The tanks - Kir Fanis, Phiniac and Scuba - have sat overnight on tissue, and all tissues are dry.

 

[nelsonm64]

any flooding of the cup with the V2 if left over night? i ask because i run my sophia with the juice control open about as much as the divers feed hole is and if i leave it overnight with the juice control open i wakeup to a full ceramic cup. i then have to remove the base and sit it upside down on paper towel for a minute to drain off the excess juice...

 

[raqball]

Not a single drop with mine..

 

[finagle69]

Mine sat in my BB tank all night. Bone dry on bottom and cup was fine. Ready to keep vaping.

Sent from my HTC One using Tapatalk

 

[nelsonm64]

Not a single drop with mine..

Mine sat in my BB tank all night. Bone dry on bottom and cup was fine. Ready to keep vaping.

Sent from my HTC One using Tapatalk

thanks guys, that's encouraging...

 

[Nach]

I don't suggest passing the juice inlets over o-rings.... this is what happened in an SnP. Seems like too much of the o-ring will go inside the recessed area for the wicks. It then get pinched or shaved off as it passes through.

 

[Akdare]

I don't suggest passing the juice inlets over o-rings.... this is what happened in an SnP. Seems like too much of the o-ring will go inside the recessed area for the wicks. It then get pinched or shaved off as it passes through.

Did you wick it before you inserted it?


Sent from my iPad

 

[Nach]

No, that was a test run through the tank to ensure fit. It was lubed up with VG though. Trying to discern whether its the fault of the Diver or the SnP.