Atmistique Atomizers
- Thread starter billakosgr
- Start date
- th_trl_thread_readers 0
- Status
Please sort out all this and let us know what works best rockin that BB. Pics can follow anytime.
raq~ ((please)) some pics of that sexy box. Also with the door open so we can see Diver plopped in
Sorry for the crappy photos but here you go..
Just refilled the tank but left the V2 pin in for now..
No juice on outside of tank.. The Diver pin contact area of the BB did have a very minor (1/4 of a drop, if even that) of juice but no worries there at at all..
I will vape up this tank and report back.. If I get gurgling / flooding again when the juice level is just obove the Diver slots then I will try the V1 pin..
I have a 3 ohm coil and rocking the BB at 5.25 V..
Awesome vape, this might just become my favorite combo with a quickness!
No juice on outside of tank.. The Diver pin contact area of the BB did have a very minor (1/4 of a drop, if even that) of juice but no worries there at at all..
I will vape up this tank and report back.. If I get gurgling / flooding again when the juice level is just obove the Diver slots then I will try the V1 pin..
I have a 3 ohm coil and rocking the BB at 5.25 V..
Awesome vape, this might just become my favorite combo with a quickness!
Same spot (juice level just above the Diver slots) and gurgling / flooding is back...
Back of tank and inside the BB all juiced up..
V1 pin here I come!
Will test and report back..
Back of tank and inside the BB all juiced up..
V1 pin here I come!
Will test and report back..
Last edited:
Hey there Raq, Ive been bouncing back and forth between pins, and for me the v1 pin is actually worse at the moment. With the v2 pin, I can leave mine upright all night, get about 2/3rds of a tank gone, and then boom, gurgle flood leak. I've been trying the v1 pin lately. Starts out good, but overall I'm getting about 3 flood and leak occurrences per tank with the v1 pin vs. 1 occurrence with the v2 pin.
I've been trying like hell to solve this with no luck. I will get really close, and then crash and burn. Keep us posted if you figure anything out.
Someone has posted that they have had great success with the v1 pin. I wish I could say the same
Changed it out and rocking the V1 pin now.. I will see how it goes..Hey there Raq, Ive been bouncing back and forth between pins, and for me the v1 pin is actually worse at the moment. With the v2 pin, I can leave mine upright all night, get about 2/3rds of a tank gone, and then boom, gurgle flood leak. I've been trying the v1 pin lately. Starts out good, but overall I'm getting about 3 flood and leak occurrences per tank with the v1 pin vs. 1 occurrence with the v2 pin.
I've been trying like hell to solve this with no luck. I will get really close, and then crash and burn. Keep us posted if you figure anything out.
Someone has posted that they have had great success with the v1 pin. I wish I could say the same
Someone has posted that they have had great success with the v1 pin. I wish I could say the same
I use what's posted on the internet as a reference material to help me with my own experience/experiment. And, I find that there tends to be a lot of hyperbole (or simply other's experience may not translate to my own).
Not much use with the V1 pin and it's leaking worse than an Iraqi submarine out of the pin...
A few drops of juice on the BB connector and juice inside BB and on back of tank..
Okie dokie.. I will rebuild and try the V1 pin again..
A few drops of juice on the BB connector and juice inside BB and on back of tank..
Okie dokie.. I will rebuild and try the V1 pin again..
Hey there Raq, Ive been bouncing back and forth between pins, and for me the v1 pin is actually worse at the moment. With the v2 pin, I can leave mine upright all night, get about 2/3rds of a tank gone, and then boom, gurgle flood leak. I've been trying the v1 pin lately. Starts out good, but overall I'm getting about 3 flood and leak occurrences per tank with the v1 pin vs. 1 occurrence with the v2 pin.
I've been trying like hell to solve this with no luck. I will get really close, and then crash and burn. Keep us posted if you figure anything out.
Someone has posted that they have had great success with the v1 pin. I wish I could say the same
How is the draw with the v1 pin installed?
The issue seems to be that the draw with the v2 pin is too tight, so the v1 pin should be giving you a looser draw.
What build are you using? If cotton, make sure you have enough wick - too little wick in the two slots will make it flood eventually.
The draw with the V1 pin (for me at least) is a little looser but not by a whole lot..
Oddly, when I 1st plopped the Diver in with the V1 pin I got a closed / tight, tight, tight draw.. Not sure why that was but I removed the tank and pushed on the pin, plopped it back in and all was good.. That super tight initial draw with the V1 pin could be why I got leaks rather fast..
I've run at least 7-8 tanks worth of juice now with one coil using the v1 pin. I've rewicked the cotton twice. I have not had a single flood, gurgle or leak. I have had juice on the back of the tank, but none on the bottom or on the Diver's 510 connector. I only noticed the juice on the back of the tank when I removed it to check it - it did not affect the interior of the Diver or the vape experience.
I'd say this is one of the few threads where you will find little to no hyperbole. Every single issue comes to light here.
V, give us some info on your setup, let's see if we can figure it out.
Pin probably didn't go in straight. How did you manage that? I can't not get the pin in straight...
One thing to note with the BB: do not tighten down the bass nut too much. Barely more than where you first meet resistance should be enough. If you tighten it down a lot, it will press the Diver's 510 down, compressing the o-rings on the pin and perhaps over the bottom, which could lead to a tighter draw as well.
Last edited:
I am at the same point with the V1 pin (juice level wise) as I was with the V2 pin.. No gurgling so I pull the tank and it's pretty dry. A micro drop on the BB pin connector but so minor as it's non important..
My initial failure with the V1 pin might have been caused by the super duper initial tight draw I was getting. I did take 5 or 6 draws with it super duper tight and have temporarily chalked the flooding with the V1 pin up to that..
The vape from the BB / Diver combo is phenomenal..
I will keep testing away but I do believe Kataphraktos is onto something here with the V1 pin...
My initial failure with the V1 pin might have been caused by the super duper initial tight draw I was getting. I did take 5 or 6 draws with it super duper tight and have temporarily chalked the flooding with the V1 pin up to that..
The vape from the BB / Diver combo is phenomenal..
I will keep testing away but I do believe Kataphraktos is onto something here with the V1 pin...
I think it was a combo of both.. I did crank the brass nut down a bit much and I do think the ceramic was not seated (crooked pin)..
Vaping like a beast now with the V1 pin.. See above
Alrighty, first of all: the v1 pin, and the whole tight draw causing over-wicking issue, was not my idea or analysis, the idea belongs to Akdare and greigster. I'm just the can't-stop-running-his-bloody-mouth Greek making sure every last Billet Box is functioning like Scotty's warp coils.
And that last bit - the resulting vape - is why I'm so fanatical about getting every last v2 Diver working, and hopefully converting some more carto users to it as well.
Honestly, when I got the BB, I figured I'd get a great-looking device that was easy to pocket, with a merely acceptable vape. What I've gotten is a shockingly great vape. So great, in fact, that a lot of other devices sit untouched, and I am considering whittling down my collection as a result.
Yeah, and I've been booked solid this week with client appointments...don't know whether to fire my assistant, or give her a raise!
I will return in a couple of days with more results.
Sent from my iPad
I will return in a couple of days with more results.
Sent from my iPad
Diver V2s (Enezlis - three or four of them) with V2 pin and micro coil (usually 1.5, now have 1.78) and organic cotton. Used exclusively in BBs. No significant issue to report (either draw or significant leaking). No condensation in the back of the tank which I attribute to new BB brass ring.
What are you going to figure out?
Oh Lord, I assumed you were having issues. I didn't realize they were working fine for you.
That's what 28 months without a single day of vacation gets you. *sigh*
- Status
Similar threads
- Locked
