Atmistique Atomizers

[sircharles]

September (my fault)

for flangeless diver?
or hippo v2?

 

[eratikmind]

for flangeless diver?
or hippo v2?

I could be wrong, but I think Konstantinos meant the Hippo V2 will be available in September.

- Andy

 

[sircharles]

I could be wrong, but I think Konstantinos meant the Hippo V2 will be available in September.

- Andy

thats what i thought too
i guess ill be ordering soon then
will just get hippo v2 in september

 

[eratikmind]

thats what i thought too
i guess ill be ordering soon then
will just get hippo v2 in september

That was my reasoning, as well. Enjoy your order when you receive it.

- Andy

 

[Apocalypse]

The Grail, another Diver, a Tapas drip tip, and a Driver. Here is a pic of the Driver. Personally, I think it's a excellent tool for the Diver or any carto.
View attachment 229911

- Andy

Found this to be a god send also....

http://www.atmistique.gr/en/siam-mo...page_images.tpl&product_id=122&category_id=38

 

[tmcase]

Here's my Diver in an unknown tank. If anybody can id this tank I'd appreciate it. I'll get a shot of the Diver in a Phiniac when I swap tanks.

 

[teamreidy48]

this looks like the x8 tank

Here's my Diver in an unknown tank. If anybody can id this tank I'd appreciate it. I'll get a shot of the Diver in a Phiniac when I swap tanks.

 

[tmcase]

this looks like the x8 tank

Yep, that's it. Thank you.

 

[nightfell]

I've been having an awful time trying to twist join NR to R, I keep twisting stuff to thick to fit through the holes. Tonight I'm going to try the Greek knot. If I fall I'm going to pick up the pre welded wire. Ms case quick question on the pre welded, is it easy to tell where the weld is?

 

[Kataphraktos]

I just received a Zapper I picked up in the classifieds. After a few minutes and attempts figuring out how long to charge up the jolt before firing, I built my first near-perfect NR/R/NR wire from Nickel and 32g Kanthal A1. Prior to this, I did make a wire for my eBDP (same CE2 ceramic insert as the Diver's) using the Western Union know (it is on Wikipedia), and although it came out uglier than Amanda Bynes, it works like a champ.

Get a Zapper. (And, Konstantine, make one of these - there's money to be made!)

 

[Technonut]

I've been having an awful time trying to twist join NR to R, I keep twisting stuff to thick to fit through the holes. Tonight I'm going to try the Greek knot. If I fall I'm going to pick up the pre wielded wire. Ms case quick question on the pre wielded, is it easy to tell where the wield is?

Yes, it is...

 

[Firestorm]

Even if you cannot see the join, you can feel it if you pull your fingers across the wires.

 

[Konstantinos]

sircharles: Hippo V2 and some flangless Diver will be available September again

nightfell: every start have difficulties but trust me in a few days u will see how easy it is

Kataphraktos-patrida: kathenas ekei poy einai tagmenos

 

[tmcase]

I've been having an awful time trying to twist join NR to R, I keep twisting stuff to thick to fit through the holes. Tonight I'm going to try the Greek knot. If I fall I'm going to pick up the pre welded wire. Ms case quick question on the pre welded, is it easy to tell where the weld is?

On the pre-welded wires it's not so easy to see the weld because they are so tiny but you can see and feel it if you look closely.

 

[sircharles]

sircharles: Hippo V2 and some flangless Diver will be available September again

nightfell: every start have difficulties but trust me in a few days u will see how easy it is

Kataphraktos-patrida: kathenas ekei poy einai tagmenos

thanks
be ordering some other stuff earlier then

 

[synic]

I've been having an awful time trying to twist join NR to R, I keep twisting stuff to thick to fit through the holes. Tonight I'm going to try the Greek knot. If I fall I'm going to pick up the pre welded wire. Ms case quick question on the pre welded, is it easy to tell where the weld is?

I must be confused. Should you be trying to feed the join part through any holes?

 

[eratikmind]

I must be confused. Should you be trying to feed the join part through any holes?

No, the NR/R joints should be touching the wicking material.

- Andy

 

[nightfell]

They are, but my twist for the join is coming out too long

 

[tmcase]

They are, but my twist for the join is coming out too long

You probably don't need so many twists.

 

[Firestorm]

Can you wrap it around the wick? If your join is the length from the wick to the holes at the bottom then it is definitely too big. If your join is lodged in the side slot of the ceramic cup, see if you can use a tool to push it in a bit so it doesn't snag.