Atmistique Atomizers

[Technonut]

Hrmm, I thought they were, but maybe I'm misunderstanding what you mean. In the first picture, if I fold them down, they are just to the threads.

I trim the wick-ends close to the ceramic.. Works well for me..

 

[synic]

Honestly, I've not had much luck with ekowool at all, in any rba. Maybe that's just because I'm judging whether or not it's burning by if I can hear a hiss after I stop pressing the button on my mod. Normally that means something's wrong, but maybe with ekowool that's normal...

 

[eratikmind]

I see a long neg leg in those pics. Break that off at where the ceramic cup pinches it at the base unit. There should no exposed wire there.

- Andy

 

[tmcase]

Honestly, I've not had much luck with ekowool at all, in any RBA. Maybe that's just because I'm judging whether or not it's burning by if I can hear a hiss after I stop pressing the button on my mod. Normally that means something's wrong, but maybe with ekowool that's normal...

I think that hissing is your mod. I have a couple mods that no matter what I put on them won't shut off immediately after taking my finger off the button. I get much better flavor with ecowool and I don't know why but it could be because it retains more juice longer than silica and it doesn't burn as fast as silica. It's all I use now.

 

[synic]

I think that hissing is your mod. I have a couple mods that no matter what I put on them won't shut off immediately after taking my finger off the button. I get much better flavor with ecowool and I don't know why but it could be because it retains more juice longer than silica and it doesn't burn as fast as silica. It's all I use now.

Can't be the mod - it doesn't do it with regular sillica, and it's a mech mod (Precise ELA or the Paps)

 

[synic]

I see a long neg leg in those pics. Break that off at where the ceramic cup pinches it at the base unit. There should no exposed wire there.

- Andy

It shouldn't cause dry hits, though?

 

[eratikmind]

It shouldn't cause dry hits, though?

That I cannot definitively answer. However, I do know that it is not required to be there. Perhaps, it does displaced e-juice . . . Who knows?

- Andy

 

[tmcase]

It shouldn't cause dry hits, though?

Have you tried putting it in a different tank?

 

[Konstantinos]

It shouldn't cause dry hits, though?

Forgive my late reply
If i notice right u use triple 2.0mm? if so pls make sure that u havent overtighten the coil to the wick
I suppose u use with/without res
The wicks dont close the body hole
Volts/Ohms u use?

 

[Konstantinos]

Diver available again

http://www.atmistique.gr/en/craven-...page_images.tpl&product_id=480&category_id=75

 

[synic]

Forgive my late reply
If i notice right u use triple 2.0mm? if so pls make sure that u havent overtighten the coil to the wick
I suppose u use with/without res
The wicks dont close the body hole
Volts/Ohms u use?

In the picture it's double 2mm. It's with NR wire, heat welded with tsaf.

Volts are unregulated 3.7 battery, I got 1.4 ohms on that build.

 

[Konstantinos]

I suggest to use with/without wire. Do u also use our ready coil?

 

[Apocalypse]

Hi Konstantinos,

I recieved both of my Divers yesterday and the Siam mods glass tanks I have set up both of the Divers with the supplied coils and wicks but I am getting a burnt taste. At first they vape beautifully but then its like the wicks are not keeping up with my vaping? I get a huge vape of burnt taste. If i let the diver stand for a short time the vape goes back to being fine but after a few long vapes its back to the burnt taste again. Any suggestions please.

 

[synic]

I suggest to use with/without wire. Do u also use our ready coil?

I am using both 32gauge kanthal and 30gauge NR silver wire. I used the ready coil, but not for long since 2ohms was too high for my mechanical device.

 

[Apocalypse]

Hi Konstantinos,

I recieved both of my Divers yesterday and the Siam mods glass tanks I have set up both of the Divers with the supplied coils and wicks but I am getting a burnt taste. At first they vape beautifully but then its like the wicks are not keeping up with my vaping? I get a huge vape of burnt taste. If i let the diver stand for a short time the vape goes back to being fine but after a few long vapes its back to the burnt taste again. Any suggestions please.

NOTE TO SELF - overfilling tank will cause dry hits DOH!!!!!

 

[STVNMR]

NOTE TO SELF - overfilling tank will cause dry hits DOH!!!!!

How full did you end up filling your tank to get good results? I just started with a half tank so as not to overdo it, but I'd like to get as much as possible in there before going out and about.

I think I remember someone saying 1/8" from the top?

 

[STVNMR]

Just got my first Diver in this morning, by the way. This thing tastes great.

 

[eratikmind]

How full did you end up filling your tank to get good results? I just started with a half tank so as not to overdo it, but I'd like to get as much as possible in there before going out and about.

I think I remember someone saying 1/8" from the top?

Since getting my first Diver some 2 months ago, I have been filling the tanks with a continuous gap left at the top of the tank.

- Andy

 

[Konstantinos]

Synic: 1.4Ohm with a mechanical mod u will need a very good feed. Pls try a triple wick in your resistance.
Also sorry to write this again but check that Divers hole make a triangle with ceramic slots.

Apocalypse: an overfilling tank probably create this issue because there is no air on it to help the feeding.
Do u still have the same problem while the tank empty a bit?

 

[Apocalypse]

How full did you end up filling your tank to get good results? I just started with a half tank so as not to overdo it, but I'd like to get as much as possible in there before going out and about.

I think I remember someone saying 1/8" from the top?

1/8" is perfect