When using the twisting method, trim the twisted NR/R joint back prior to wrapping the twisted joint with the NR leg. That should help you reduce the size.
- Andy
- Andy
Atmistique Atomizers
- Thread starter billakosgr
- Start date
- th_trl_thread_readers 0
- Status
How long does it usually take for the shipment to arrive from Greece to the USA? Did you also get a tracking number with your order?
it took about a week from my order date
i don't remember getting a tracking number
I'm about to order Grail and some other stuff
any reviews on the grail yet?
My Zapper arrived today!!! My Killer, Diver, and Euforia will have pro wicks and coils for-evah!!!
My Grail has been sitting at the ISC NYC for the past 3 days. Some times it quicker. Some times its slower. The quickest from Atmistique was 7 days, back in May.
- Andy
- Andy
it took me maybe two to two and a half weeks to receive my diver when i ordered it. above average from overseas. this company is wonderful.
Any ISC is 'custom hell', my Grail was stuck at ISC New York from 7/6 until 7/12 before its moved to another stop (in my case, Flushing, since I am in NYC), so hopefully it'll arrive Monday, make it total around 12 days.
I've had a pkg in ISC New York since the 6th too.... Still hasn't left there. Customs sucks.
Yep, here I thought the brass ring was the one piece I would never need or want, but now with a Paps Lux incoming, that might change as well...
I didn't think so either, I'm glad that I have that brass accent ring, now.
- Andy
Hey guys, I'm sure this has been asked many timed before, but I've been looking for the past 30 minutes, and can't find what I'm looking for.
I want to use my diver, but I vape 70pg/30vg juice. Will this be to thin for the diver. When I look at the parts, I just don't see how this thing is not going to flood. I hope it works out, I really want to get the cartos out of the billet box.
Thanks in advance for any help guys.
I want to use my diver, but I vape 70pg/30vg juice. Will this be to thin for the diver. When I look at the parts, I just don't see how this thing is not going to flood. I hope it works out, I really want to get the cartos out of the billet box.
Thanks in advance for any help guys.
That's the same juice ratio I use, and the Diver works fine..
I think there is some mythical Greek magic afoot on how it works without flooding.. 
I personally can't believe it doesn't flood, but the results speak for themselves. I currently awaiting delivery of a Diver I ordered for my girlfriend, I'm anxious to see how it stacks up against my Killer 705. We primarily use 60/40 blends, which seem to work fine in the Killer. As far as I can tell mythical Greek magic is the only answer!
Well, got it setup, taste great, huge vapor, but just as I suspected, leaks like a ..... I used one of the premade coils, and wicks running perpendicular to hole as directed. I'm going to tear it down tomorrow, and try again.
I really hope I get this thing working, got high hopes for this and my BB, as I absolutely hate cartos.
I noticed something. With the brass pin, and the ceramic in, I cant get both to seat all the way. If you fully seat the pin, the cup gets pushed up on the topside, and if you seat the cup, the pin gets pushed out at the bottom. Is this normal?
I really hope I get this thing working, got high hopes for this and my BB, as I absolutely hate cartos.
I noticed something. With the brass pin, and the ceramic in, I cant get both to seat all the way. If you fully seat the pin, the cup gets pushed up on the topside, and if you seat the cup, the pin gets pushed out at the bottom. Is this normal?
Where is it leaking? Out of the carto connection hole?
I had problems seating the ceramic when I was using 30 ga wire. It was too thick. That was when I wasn't using NR wire. I'm now using 32ga silver and the cup seats tight. I press the cup and pin together with my fingers and if that doesn't work then I set it on my counter and use a small piece of wood/board on the top of the cup and press down. You might have to pull the pin out a little ways doing it this way because it might not make a good connection.
Yes, its leaking out of the bottom at the pin, and I'm using the 32 ga. Wire. About parts not seating, they dont seat even without a coil/wick. Its like the pins are too long or something. It doesn't leak if I lay it flat, just when it's standing vertical like it would be in my shirt pocket.
- Status
Similar threads
- Locked
