There is an o-ring that goes around the middle, and the beauty ring goes over that.
Atmistique Atomizers
- Thread starter billakosgr
- Start date
- th_trl_thread_readers 0
- Status
Excellent! I was wondering why I had so many orings!! Thanks a bunch! I'm about to load the diver up and go for a swim!!
This is too funny!! I was putting the orings and rings on my spare tubes and I was like....dang....this ring is way tool small with the oring, but the other tube was fine...I finally noticed that different size orings tool!! I am so "not" mechanical but I did figure it out without asking another dumb question! These scuba tanks look awesome with the different center rings!! Thanks!Many tanks need many spare o-rings
Holy crap! Well I just found out I screwed up, I ordered 8 dual coil cups. Turns out it was 8 five packs. Lol
Z There are no stupid questions. Scuba needs 6 o-rings (1 bigger to 6 smaller):
1. 2 x o-rings for the tops of the tube
2. 1 x o-ring for the center
3. 2 x inner o-rings
4. 1 x o-ring for filling port
I also like to change them often, depending on the mod i use and my mood
pmuniz if you think that is not clear in the description we must change it somehow
1. 2 x o-rings for the tops of the tube
2. 1 x o-ring for the center
3. 2 x inner o-rings
4. 1 x o-ring for filling port
I also like to change them often, depending on the mod i use and my mood
pmuniz if you think that is not clear in the description we must change it somehow
No it is probably clear, but to be honest it was my fifth day in Vegas (when I put the order in) and we all know how that goes...
Also I don't mind having extra cups
Got my scuba today!
Where do you find a scuba without the middle ring?
Sent from my Galaxy Note 3 using Tapatalk 4
Right here... http://www.atmistique.gr/en/new-pro...page_images.tpl&product_id=608&category_id=96
Select without center ring.
Got my scuba today!
I just got my Stealth Mini yesterday. That looks gorgeous.
Pmuniz the green inside is
very beautiful
Thanks! It's a special mix, Heisenberg!
I got the diver set up today in my new scuba tank!! So far so good....nice vape...draw is a little tighter than I like so I may have to throw a hippo on and see if that will help! I had a black pro ring on but changed it since the little silver fill tab sticks slightly out as you can see in the picture, wish that tab was black but oh well, I am enjoying the vape!!
Edit: this baby is really putting a nice warm vape and great vapor!! Tried AIV 15 Foot Falls juice since AIV do not recommend cartos or clearos because there is a small amount of NET in this juice, Nice!!
Edit: this baby is really putting a nice warm vape and great vapor!! Tried AIV 15 Foot Falls juice since AIV do not recommend cartos or clearos because there is a small amount of NET in this juice, Nice!!
Last edited:
Z try to align the pin slot with base slots
Nice combo also but i prefer the previous black combo
Nice combo also but i prefer the previous black combo
Been using my diver v2 flangless for about a week now inside of the Bayou by Atmizoo, and I'm getting leaks every time I fill, and sometimes throughout the day. Today, I noticed that the leaking is coming from the pin at the bottom of the diver. I'm also getting a consistent flooding after this recent (10 min ago) refill.
Any suggestions. This thread is way over 300 pages long and hard to search. Thanks.
Jason
Any suggestions. This thread is way over 300 pages long and hard to search. Thanks.
Jason
I see now that my juice holes have no visible cotton extruding. I guess I used too little cotton for my wick. Is there anything else one might suggest?
With the Diver inside while you fill your tank the juice go inside the base hole and you have leakage.
So pls do this:
1) Use carto tool or something similar and slide the Diver out just enough so the Diver juice hole is outside of your tank
2) Open fill port
3) Fill
4) Close fill port
5) Slide Diver back into the tank
You can also fill it with the Diver inside by close with your fingers the tube and the 510 hole. With this way i am not sure that you will have good results.
About the cotton you must use in your micro-coils pls take a look here: How to: Micro-coil in Diver V2 - YouTube
So pls do this:
1) Use carto tool or something similar and slide the Diver out just enough so the Diver juice hole is outside of your tank
2) Open fill port
3) Fill
4) Close fill port
5) Slide Diver back into the tank
You can also fill it with the Diver inside by close with your fingers the tube and the 510 hole. With this way i am not sure that you will have good results.
About the cotton you must use in your micro-coils pls take a look here: How to: Micro-coil in Diver V2 - YouTube
Thank you, Konstantinos. I appreciate you responding so quickly.
I find with any wick material - and I use cotton balls as well - you need to have enough to completely cover the slots on the side of the Diver. They don't need to protrude form the slots, but the wick needs to be enough so that the slots are full without being too densely packed to choke off juice flow.
I have the amount down well enough that I can re-wick both my v2 Divers in a few minutes and get the amount right every time.
I build the microcoil (I assume with cotton you are using a microcoil) to be 2mm diameter, and leave most of the coil exposed above the upper lip of the cup. This way:
1. I can pass enough cotton through the coil so that there is enough to fill the external slots completely with wick, without getting the cotton choked up in the two slots of the ceramic cup.
2. Some of the coil is still inside the cup, so when I rewick, the shear force of pulling the old cotton and inserting the new cotton doesn't damage the coil by pressing it back and forth.
- Status
Similar threads
- Locked
