Atmistique Atomizers
- Thread starter billakosgr
- Start date
- th_trl_thread_readers 0
- Status
All day, vaping awesome.
Sent from my HTC One_M8 using Tapatalk
It fits? Fantastic! My Hana should be here Saturday, that might be Eviva's home.
Yeah you just have to "adjust" the airflow control to take into consideration the rotation required to snug it down once it grabs the ring. The other thing is the 510 needs to be adjusted out quite a bit to stop the "check atty".
Once this tank is cleared I'm gonna wrap up a 1.4 ohm coil so I can enjoy some nice 20 watt regulated vape.
Makes me wonder what K did to allow it to wick so well with just one juice inlet. My thought is the deck is lower than the juice "pressure level" meaning there is always a good supply of ejuice on the wicks. Only way I can explain how it keeps both sides wicked while in tank mode.
Once this tank is cleared I'm gonna wrap up a 1.4 ohm coil so I can enjoy some nice 20 watt regulated vape.
Makes me wonder what K did to allow it to wick so well with just one juice inlet. My thought is the deck is lower than the juice "pressure level" meaning there is always a good supply of ejuice on the wicks. Only way I can explain how it keeps both sides wicked while in tank mode.
Ordered Monday, delivered in Australia on Friday. Not bad at all! Haven't built it yet (I'm "working"), but it looks and feels great 
That just looks incredible on a Provari! Makes me sad I sold mine, just until I pick up the Hana sitting on my desk
That just looks incredible on a Provari! Makes me sad I sold mine, just until I pick up the Hana sitting on my desk
Yeah I just gave my dad my chrome v2 for the second time. It kinda makes me wish I could bring the two together!
Quick rebuild with a 10 wrap on 27g wire. I used the broken CE cup for this one since it would be impossible given the size of the coil. Instantly I started to pic up even more sweeter notes from the ejuice (same juice as my first build). Can't wait to get the SS cup adaptor.
1.3 ohms is much better.
Sent from my HTC One_M8 using Tapatalk
1.3 ohms is much better.
Sent from my HTC One_M8 using Tapatalk
Is there enough material on the airflow ring to make the transition from 23 to 22mm?
Sent from my HTC One_M8 using Tapatalk
Sent from my HTC One_M8 using Tapatalk
Update, so I have been running the Eviva T and D for just about 3 days now. Everything is working flawless.
I think I figured out how the juice flow works so great. I think when you put the top cap on and tighten it down it creates pressure which keeps the juice flowing from the juice tank to the wick.
I think I will re-coil/wick them today and try with cotton.
I think I figured out how the juice flow works so great. I think when you put the top cap on and tighten it down it creates pressure which keeps the juice flowing from the juice tank to the wick.
I think I will re-coil/wick them today and try with cotton.
I suspect the reason you have to flip the Eviva before finishing tightening down the top cap is that the pressure produced as it tightens down might flood the chamber a bit. Doing so while the Eviva is upside down means air enters the chamber as it tightens down, instead of liquid.
It's same reason as filling the Kayfun from the top.
Sent from my HTC One_M8 using Tapatalk
Just like a Kayfun that people choose to top fill rather than remove from mod for bottom filling. Have to flip it over so it doesn't flood.
Sent from a BIG phone.....Galaxy Note 3
Hahahaha! Guess I had reply window open too long. Didn't see this post.
Sent from a BIG phone.....Galaxy Note 3
OK this worked but is a PIA to hold & twist just right.
I think the diver needs reverse threading.
That aside I can't wait to get another!
Sent from a BIG phone.....Galaxy Note 3
You have to flip right just as the top oring touches the cap - 1/4 too much and you fill the chamber with juice and it runs out into your hand
- Status
Similar threads
- Locked
