Attack of the Hana Modz Clone. Let's wait together!

[retird]

They seemed to have taken a calculated risk and lost. Now they're trying to make up for it by suing. They should go after the logo-ed clones. It's clearly a TM infringement. But to go after those who aren't using logo-ed clones is simply taking their ball and going home, pissy that they list their bet, with another company flooding the market with lookalike clones at a much cheaper price. They shouldn't be rewarded for losing a gamble.


Sent from my iPhone using Tapatalk

It's not just about TM infringement/logo's.... you might want to read this....it is an 8 page pdf of the court filing.... just fyi.... hope this helps

hana modz v daily vape steals.pdf

 

[Iceclouds]

Epoxy is a permanent solution. It can contact the solder points as long as there is no metal in the Epoxy (don't use JB Weld!)

If not JB Weld what would you suggest...have never used any so all suggestions would help.

 

[Steve58]

Received today from WetVapes quick shipping great customer service
They threw in a bottle of juice too

 

[215Z]

It's past midnight in Shenzhen, Guangdong. I'll have to wait until their morning - my evening - to finalize things with them. I confirmed that they can send me a mixed case (3 red, 3 blue, 3 green, 1 silver), but I'm waiting to hear if I can get a custom Startup Screen.

The "hana modz" startup is disrespectful and in poor taste. I'm hoping they can have it say Shenzhen Cloupor, or my name at worst. I have seen pictures of non-Cloupor made clones that say "evolve dna" at startup, so I know it is not set in stone. For all I know, they have not yet heard feedback that users overwhelmingly are disgusted with any references to Hana on their boxes.

I also made it clear that I would cancel my order if they can not ship it out according to their projected timeline.

 

[BigDaddyQ]

If not JB Weld what would you suggest...have never used any so all suggestions would help.

Ok I think there is a bit of confusion over what to and what not to use. JBWeld and LocTite are brand names. They both make similar products. Including both conductive, and non-conductive epoxy. If you want a non conductive expoy that's stronger than say, hot glue, I'd recommend either JB Weld's Clear Weld or LocTite Stik'n'Seal maybe. If you are bad with a soldering iron and want to use a conductive epoxy instead, LocTite 3888 conductive expoy compound might do the trick.

 

[retird]

It's past midnight in Shenzhen, Guangdong. I'll have to wait until their morning - my evening - to finalize things with them. I confirmed that they can send me a mixed case (3 red, 3 blue, 3 green, 1 silver), but I'm waiting to hear if I can get a custom Startup Screen.

The "hana modz" startup is disrespectful and in poor taste. I'm hoping they can have it say Shenzhen Cloupor, or my name at worst. I have seen pictures of non-Cloupor made clones that say "evolve dna" at startup, so I know it is not set in stone. For all I know, they have not yet heard feedback that users overwhelmingly are disgusted with any references to Hana on their boxes.

I also made it clear that I would cancel my order if they can not ship it out according to their projected timeline.

hum... you getting 10 for yourself.....

 

[BigDaddyQ]

It's past midnight in Shenzhen, Guangdong. I'll have to wait until their morning - my evening - to finalize things with them. I confirmed that they can send me a mixed case (3 red, 3 blue, 3 green, 1 silver), but I'm waiting to hear if I can get a custom Startup Screen.

The "hana modz" startup is disrespectful and in poor taste. I'm hoping they can have it say Shenzhen Cloupor, or my name at worst. I have seen pictures of non-Cloupor made clones that say "evolve dna" at startup, so I know it is not set in stone. For all I know, they have not yet heard feedback that users overwhelmingly are disgusted with any references to Hana on their boxes.

I also made it clear that I would cancel my order if they can not ship it out according to their projected timeline.

Only the 1:1 clones from Cloupor I've seen so far have the Hana Modz start screen. The non logoed units I've seen thus far just go straight to the main screen.

 

[retird]

Ok I think there is a bit of confusion over what to and what not to use. JBWeld and LocTite are brand names. They both make similar products. Including both conductive, and non-conductive epoxy. If you want a non conductive expoy that's stronger than say, hot glue, I'd recommend either JB Weld's Clear Weld or LocTite Stik'n'Seal maybe. If you are bad with a soldering iron and want to use a conductive epoxy instead, LocTite 3888 conductive expoy compound might do the trick.

hum... conductive JBWeld....may come in handy... ya got a link to it as I can't find it....thx

I see where JBkwik may be slightly conductive but not JBWeld....now you have me confused...

 

[215Z]

hum... you getting 10 for yourself.....

I will keep three or four for myself+household.
At a 1 in 5 failure rate, I expect two to be sold @ 75% cost to SX350/DNA30 modders.
Of course I will be testing each unit rigorously to find the two ugly ducklings, with both 0.8ohm and 2.2ohm toppers.
I'll take the remaining 4 or 5 into my local B&M's and try to make friends, and if that fails I'll put them up on ebay.

 

[BigDaddyQ]

hum... conductive JBWeld....may come in handy... ya got a link to it as I can't find it....thx

I see where JBkwik may be slightly conductive but not JBWeld....now you have me confused...

Clear weld from JB weld is non conductive. KwikWeld is a different JB Weld product and is "steel reinforced" so it may be conductive.

 

[xtwosm0kesx]

It's not just about TM infringement/logo's.... you might want to read this....it is an 8 page pdf of the court filing.... just fyi.... hope this helps

hana modz v daily vape steals.pdf

Seeking damages of $150,000 for EACH infringement, that's some serious money...

 

[keithvi]

hum... conductive JBWeld....may come in handy... ya got a link to it as I can't find it....thx

I see where JBkwik may be slightly conductive but not JBWeld....now you have me confused...

Silver Conductive Epoxy: 10 Mins. Working Time / High Conductivity


8331
- See more at: Silver Conductive Epoxy: 10 Mins. Working Time / High Conductivity | MG Chemicals

 

[DFireOnly]

Seeking damages of $150,000 for EACH infringement, that's some serious money...

So if it's a trial by jury. Then you get a jury of your peers. Does that mean we will have a jury of vapors. I think it should be by ones who bought the clones. lol. Lots of vaping in that court room. lol


Sent from my iPad using Tapatalk

 

[retird]

I will keep three or four for myself+household.
At a 1 in 5 failure rate, I expect two to be sold @ 75% cost to SX350/DNA30 modders.
Of course I will be testing each unit rigorously to find the two ugly ducklings, with both 0.8ohm and 2.2ohm toppers.
I'll take the remaining 4 or 5 into my local B&M's and try to make friends, and if that fails I'll put them up on ebay.

Soiunds like ya got a plan..... the B&M will like you if they get a free-gratus....

 

[retird]

Silver Conductive Epoxy: 10 Mins. Working Time / High Conductivity


8331
- See more at: Silver Conductive Epoxy: 10 Mins. Working Time / High Conductivity | MG Chemicals

THX.... thought I'd lost it JBWeld is not conductive and Silver Conductive from MG Chemicals is....So Silver will be used where I need conductivity... THX a bunch...

 

[BigDaddyQ]

Seeking damages of $150,000 for EACH infringement, that's some serious money...

In the VaporTek USA case, as long as they didn't sell any "logo'ed" units, there's only the use of the photo in their advertising to consider.

 

[retird]

So if it's a trial by jury. Then you get a jury of your peers. Does that mean we will have a jury of vapors. I think it should be by ones who bought the clones. lol. Lots of vaping in that court room. lol


Sent from my iPad using Tapatalk

ROFLMAO......Can just see CNN headlines now "clouds of vapor hiding the partial jury".....

 

[mykereid]

If you read the brief filed by Hana, you'll see that Daily Steals used a Hana-produced image of the Hana Modz. They aren't shooting in the dark. Seems they know exactly who to target for trademark infringement, most of it based on what the vendors posted on their websites.

They seemed to have taken a calculated risk and lost. Now they're trying to make up for it by suing. They should go after the logo-ed clones. It's clearly a TM infringement. But to go after those who aren't using logo-ed clones is simply taking their ball and going home, pissy that they list their bet, with another company flooding the market with lookalike clones at a much cheaper price. They shouldn't be rewarded for losing a gamble.


Sent from my iPhone using Tapatalk

 

[mykereid]

Unless I misunderstood, it's $150,000 plus the profits made from the sale of the clones.

Seeking damages of $150,000 for EACH infringement, that's some serious money...

 

[retird]

If you read the brief filed by Hana, you'll see that Daily Steals used a Hana-produced image of the Hana Modz. They aren't shooting in the dark. Seems they know exactly who to target for trademark infringement, most of it based on what the vendors posted on their websites.

Unless I misunderstood, it's $150,000 plus the profits made from the sale of the clones.

Kinda the way I read it.....and recovery of court costs and attorney fees....