Sound like the perfect juice for a hard drinking night, when temptation might strike!
Attention: new or soon to be new Reonauts
- Thread starter Filthy-Beast
- Start date
- th_trl_thread_readers 0
- Status
Got a question:
When you look at the RBA's (HERE) for the Reo Grand, I notice it says "Reomizer 2.0" for the regular Reo Grand. However, it just says "Reomizer" for the LP Reo Grand. Are they both Reomizer 2.0? Is the Reomizer for the LP a different model?
When you look at the RBA's (HERE) for the Reo Grand, I notice it says "Reomizer 2.0" for the regular Reo Grand. However, it just says "Reomizer" for the LP Reo Grand. Are they both Reomizer 2.0? Is the Reomizer for the LP a different model?
They are the same EXCEPT...the Reomizer 2.0 has been milled at the bottom so that it will fit inside the regular grand catch cup. The LP Reomizer is not milled around the bottom and it the best choice for any LP REO grand or LP REO mini 2.1.Same exact great vape....
The Reomizer 2.0 will work on a LP REO but it looks odd because the milled portion at the bottom stick out like a sore thumb. The Reomizer LP will not work on a regular grand.
I am not positive but I believe Rob named them differently so it was less confusing.
Thanks Rattler. I'm eyeing the Brass Reomizer 2.0 for LP. I'm wondering how it would look with the Brass button sitting on the Black Wrinkle LP.
Tweaking around with an order. It's gonna be around $235 all together.
Does below look like I've gotten everything?
----------------------------------------------------------------
4 x o ring bottom fed rba 1mm X 10mm
$1.00
1 x Black Delrin Button Covers
$4.00
1 x Brass Button Covers
$6.00
2 x Springs for Metal REOs
$10.00
4 x Spring screw Metal REOs
$1.00
4 x Magnets Metal Reos
$2.00
4 x Bottles 6ml
$2.60
1 x low profile Brass reomizer works with lp mods only
$53.00
1 x LP reo grand black wrinkle
$156.00
Tweaking around with an order. It's gonna be around $235 all together.
Does below look like I've gotten everything?
----------------------------------------------------------------
4 x o ring bottom fed rba 1mm X 10mm
$1.00
1 x Black Delrin Button Covers
$4.00
1 x Brass Button Covers
$6.00
2 x Springs for Metal REOs
$10.00
4 x Spring screw Metal REOs
$1.00
4 x Magnets Metal Reos
$2.00
4 x Bottles 6ml
$2.60
1 x low profile Brass reomizer works with lp mods only
$53.00
1 x LP reo grand black wrinkle
$156.00
Last edited:
The Black Wrinkle with brass is a killer look!! Very sharp looking REO.
Your list looks good. You will get two bottles with your new REO so you will end up with 6.
The other extras, magnets, o-rings, and spring screws, are great to have around. You might want 2 extra screws for the RM2.
Parts for REO's usually last a long time. But playing it safe and ordering extras never hurts!
Instead of 4 1.0x10 get two of each 1.0 and 1.5. Reason being the 2 different thickness are for making your air hole on your RM2 line up right, the extra half millimeter can make a big difference. Be aware that there will be a piece of thread in the bag with the Brass Button Cover. You'll need to lay it over the firing button before putting the cover on. I'm not too sure you'll ever need the screws for the springs. Not more than one anyway, you should never need it unless you drop one on the carpet. For the most part looks like you're set and good to go. Purdy much the only thing I'd add to your list is another Reo. YMMV
ETA Your Ninja typing skillz are well honed Karen. The RM2 screws are good too. (doh forgot about that one)
ETA Your Ninja typing skillz are well honed Karen. The RM2 screws are good too. (doh forgot about that one)
Last edited:
Is there a most desirable spot on the RM2 for the airhole to line up? I can only get mine to line up with the end of my coil that's furthest away from the juice hole. Isn't the air hole supposed to be as close to the juice feed hole as possible? Or is it just as close to the coil as possible? I had no idea the o rings are supposed to help with that!
Actually the 1.0mm or the 1.5mm o-rings go under the RM2 to make the whole RM2 line up so the air hole is pointed up when you vape. The RM2 with the cap are married when made, the air hole when screwed on should be right in front of the coil area. They aren't perfect every time but usually close enough you can build your coil a little off set to make up for it. With that being said I have seen others put the o-ring on the RM2 but it's not usually needed.
Thanks Raynman, I misunderstood. I do have an o ring under my RM2 but thought you meant a second o ring would go inside the RM2. I'll leave mine like it is.
This is just a suggestion but the Reomizer should be listed one of 2 ways to help with all the confusion some people have. It seems everyday there is someone asking which one they should get or they couldn't find one or the other. I think Rob should either drop the 2.0 from the Reomizer and it be be listed as Reomizer and Reomizer LP or it should just be RM2 and RM2LP... I think that would clear up any confusion. Just my 
I like my air hole to line up dead center between the posts, If it does not I file the base of the cap until it does. Key is keep it perfectly flat while filing or sanding.
Since the RM2 is so close in size to my file, I constantly rotate the RM2 while filing. I check the fit often, the hole will slowly rotate clockwise around the RM2. This one rotated about 340 degrees to get to the spot I like.
Since the RM2 is so close in size to my file, I constantly rotate the RM2 while filing. I check the fit often, the hole will slowly rotate clockwise around the RM2. This one rotated about 340 degrees to get to the spot I like.
Last edited:
I have not received mine yet so I can't look but would that mess the threads up or are they higher in the top?I like my air hole to line up dead center between the posts, If it does not I file the base of the cap until it does. Key is keep it perfectly flat while filing or sanding.
Since the RM2 is so close in size to my file, I constantly rotate the RM2 while filing. I check the fit often, the hole will slowly rotate clockwise around the RM2. This one rotated about 340 degrees to get to the spot I like.
My RM2 air hole goes past the coil just enough to make it off center.
Would filing it down to spin almost one more full rotation be ok?
or would that be taking off too much?
No it does not mess with the threads there is a slight lip. You should be able to spin it all the way around. If dead center between the posts is 12 I've spun several that were at 1.
I see the option for adding the 1.0 o-ring, but not the 1.5 o-ring. Anyone know where it's at? I'll definitely add more screws for the Reomizer.
It does not have a pic but should be there http://www.reosmods.com/index.php?page=shop.product_details&flypage=flypage.tpl&product_id=985&category_id=32&option=com_virtuemart&Itemid=3
Alright, a Monday shipment should put you vaping in style by the end of the week, congrats!Found it right after I posted the question. Right in front of me.Guess I'm just excited about getting an order in tonight.
- Status
Similar threads
