after i refill, close cap, i turn upside down and turn to the airflow i want (max), then flip it upright
Augvape and Roxy Boreas RTA
- Thread starter mtbason35
- Start date
- th_trl_thread_readers 0
- Status
Only open to 1 hole, then let it slowly fill for a bit. Usually about a minute or so. Then open to your normal setting and vape
Sent from my Nexus 6 using Tapatalk
#1645 arrived from SubtankSupply this morning....Flawlessly clean with perfect threads and a day early...Cant ask for more then that!
5/6 wraps of 26 gauge K1 and she's chucking leakless clouds of blueberry cheesecake at 40 watts.
Direct or MTL with this one....I'm liking it!
5/6 wraps of 26 gauge K1 and she's chucking leakless clouds of blueberry cheesecake at 40 watts.
Direct or MTL with this one....I'm liking it!
is it me or...
everytime i refill, somehow my first few pulls produces very little vapor (max vg diy juice) and then i had to do this almost EVERY time, i grab a tissue paper, cover all the airholes, and blow out, and bam, i just lost 1ml at least, seems like after i do the "flip upside down, let juice drip out of deck to tank, then close airflow to half hole, then flip back up and refill, then close cap, flip upside down and open to desired airhole, flip back up again and vape", i almost ALWAYS have a pool of juice in the deck that i have to blow out for me to vape the boreas like normal, i've tried covering the deck, covering only the juice holes, nothing seems to stop this problem, anyone with similar issue?
everytime i refill, somehow my first few pulls produces very little vapor (max vg diy juice) and then i had to do this almost EVERY time, i grab a tissue paper, cover all the airholes, and blow out, and bam, i just lost 1ml at least, seems like after i do the "flip upside down, let juice drip out of deck to tank, then close airflow to half hole, then flip back up and refill, then close cap, flip upside down and open to desired airhole, flip back up again and vape", i almost ALWAYS have a pool of juice in the deck that i have to blow out for me to vape the boreas like normal, i've tried covering the deck, covering only the juice holes, nothing seems to stop this problem, anyone with similar issue?
Drip tip (2) 8 x 1
Top of chimney stem where fill ports are 9 x 1
Top cap 18 x 1
Glass tank seals (2) 24 x 1
Bottom of chimney stem 10 x 1
Top of afc ring 18 x 1
Below afc ring (2) 17 x 1
Base: large is 18 x 1, small in bottom is 11 x 1.2
Deck 12 x 1
I got this from Roxy
O-ring sizes
Drip tip (2) 8 x 1
Top of chimney stem (where fill ports are) 9 x 1
Top cap 18 x 1
Glass tank seals (2) 24 x 1
Bottom of chimney stem 10 x 1
Top of afc ring 18 x 1
Below afc ring, on chamber (2) 17 x 1
510 base: large one is 18 x 1, in bottom is 11 x 1.2
Deck 12 x 1
Sent from my Nexus 6 using Tapatalk
O-ring sizes from Roxy in April:
BOREAS O RING SIZES
Drip tip (2) 8 x 1
Top of chimney stem where fill ports are 9 x 1
Top cap 18 x 1
Glass tank seals (2) 24 x 1
Bottom of chimney stem 10 x 1
Top of afc ring 18 x 1
Below afc ring (2) 17 x 1
Base: large is 18 x 1, small in bottom is 11 x 1.2
Deck 12 x 1
Note to self - read to the end of the thread before post a reply
I've used needle tips like MMW and they probably work the best, but mostly I use tips similar to this since my favorite juice comes in bottles with them.
It doesn't have to fit down into the channel to fill it that way. I've filled mine with glass dropper tops, too. You just have to be a little more careful.
It doesn't have to fit down into the channel to fill it that way. I've filled mine with glass dropper tops, too. You just have to be a little more careful.
- Status
Similar threads
- Locked
