AVS with 510 = Happiness !
- Thread starter CatVTTV
- Start date
- th_trl_thread_readers 0
- Status
So it was only an empty tank? Ok Nandy, nice
Jt, if you still have the issue then can you totally close the CR and open it only 1/4 of a full turn? GGTS can adjust the air and the liquid too inside atomizer so its imposible to not find the right position for the best vaping
Thanks for that Imeo, one thing I noticed from that video, and I think its important, I noticed you screwed the top cap in place, by turning the body of the GGTSand not the cap itself, and I know I dont do this, but will from now on, as it prevents anything else being unscrewed.
I do it this way just because I like it and maybe because GG stays in place without movements, nothing more pet.
IMEO... I have been messing around and what I have found is when I start fresh I am fine... But when liquid gets down to about 2mm below the threads in the tank I lose all vacum. No fluid goes into atty unless I completely close the CR and re prime it... Vape one or two more vapes and then have to re prime.... Not sure why this is happening... All O-Rings are good and seal tightly...
Did you ever put any vasoline on the threads and o-rings of the AVS? This will help to create 100% seal. I had the same problem before I tried it.
Just need a little on the threads and enough to moisten the o-rings.
Just need a little on the threads and enough to moisten the o-rings.
Last edited:
Did it!!! Didn't work.... O rings are vasolined and solid!!! Just still lose suction on the tank,.... If I take the tank off the CR it slowly drips the liquid out through the pin.... I also tightened the pin slightly to make sure it wasn't loose... That shouldn't happen....
I just stripped it down, washed it, and put vasoline on every thread and oring... I did notice one thing though... When I screw the 510 connector with atty into the tank my Liquid controle ring rubs against the opening in the liquid tank.. It then opens the liquid control ring all the way... That shouldn't affect not getting juice to atty but it is something I noticed... Almost as if the ring is too big or the tank opening is too small!!! I topped the juice off so we will see once I vape down past the threads....
I'm not sure about that one, I've only been using my 901's I just got a 510 adapter a few days ago, but don't have any higher ohm 510 attys to use w/ it so haven't tried mine yet.
that happens because when you vape at 2mm liquid left then the liquid cant go inside hole of the atty when you vape in horizontal position. Just refill the AVS buddy
No IMEO. I mean 1-2mm below the top threads of the tank. There is barely 1ml of juice gone. It also doesn't explain why the liquid control ring doesn't fit enough when tightening the connector to the tank and it opens all the way.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
you mean that liquid control ring is open all the time inside tank? Then you would have too much liquid inside atty but you say that atomizer is not feeded.
1. what atomizer you use and to what volts?
2. Can you please change atomizer to see what happens?
1. what atomizer you use and to what volts?
2. Can you please change atomizer to see what happens?
No IMEO... the liquid control ring loosens when I screw connector into liquid tank.... the liquid isn't going into atty no matter the amount of liquid in tank... burnt taste.... I use Joye 510's... Have also tried SLB... no luck..... I used them at 6volts.... My biggest question is why am i losing all vacum on atty and tank.... there has to be some type of leak with the connector.....
when you say that you lose vacum you mean that AVS is leaking when you have it outside the GGTS? If you put it outside of GGTS and close the mouthpiece with your finger it still leaks from its pin?
Yes IMEO. If I take the avs off the GGTS top part and place my finger over the mouth hole I still get leaking. As I said all o rings are good.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
thanks EL my friend for your nice words. I always dedicate to what ever I do. I cant hold out life without passion for everything I like.
Merry Christmas to you too buddy, have nice holidays
Merry Christmas to you too buddy, have nice holidays
- Status
