Best setup for Kayfun lite plus with Kanthal 32 and 3mm wick

Status
Not open for further replies.

t8kiteasy

Ultra Member
ECF Veteran
Verified Member
Sep 22, 2012
2,690
1,980
60
virginia beach
With 32awg wire and 3mm silica I just double loop the silica and make two to three wraps (.5-.9) is where the res. is.Pull the open ends of the wick to shrink the loops into smaller loops to set on the juice well inside the KFL.it is the same as a figure eight wick easier to build.
Second build,fold the 3mm silica in half and make the same two to three wraps.Fold the ends down into the KFL juice well and cut it back to size to set on the juice well ledge.This gives a double wick on both sides and keeps up with chain vaping it is harder to get any gurgle with this build.
 

mhmdyseen

Full Member
Apr 13, 2013
17
1
United States
With 32awg wire and 3mm silica I just double loop the silica and make two to three wraps (.5-.9) is where the res. is.Pull the open ends of the wick to shrink the loops into smaller loops to set on the juice well inside the KFL.it is the same as a figure eight wick easier to build.
Second build,fold the 3mm silica in half and make the same two to three wraps.Fold the ends down into the KFL juice well and cut it back to size to set on the juice well ledge.This gives a double wick on both sides and keeps up with chain vaping it is harder to get any gurgle with this build.

Thanks. I also need to know whats the best res to go for. I need to know pros and cons of 1.9ohm and 1.5ohm u mentioned considering that Im using a mechanical mod without a kick?
 
Last edited:

t8kiteasy

Ultra Member
ECF Veteran
Verified Member
Sep 22, 2012
2,690
1,980
60
virginia beach
Thanks. I also need to know whats the best res to go for. I need to know pros and cons of 1.9ohm and 1.5ohm u mentioned considering that Im using a mechanical mod without a kick?

That's between .5 and .9 ohms with two to three wraps of 32awg.As far as the vape goes there is really no real significant difference between .5 and .9 resistance,other than .5 does get a little warmer,not much,but a little.If you are using a battery that has a 10A limit you can safely wrap a .5 coil but DO NOT go below that.It WILL heat up the battery tube and button quick.

I usually have all my RBA/RTA's wrapped with a .5 coil (3mm silica or 1/8" ceramic Rope Wick).This is my sweet spot for vaping and it is a STELLAR,juicy flavorful vape in a Russian 91%.Make sure you make a slightly loose wrap at .5 (if you chain vape) or you will have problems with it not wicking fast enough.
 

mhmdyseen

Full Member
Apr 13, 2013
17
1
United States
That's between .5 and .9 ohms with two to three wraps of 32awg.As far as the vape goes there is really no real significant difference between .5 and .9 resistance,other than .5 does get a little warmer,not much,but a little.If you are using a battery that has a 10A limit you can safely wrap a .5 coil but DO NOT go below that.It WILL heat up the battery tube and button quick.

I usually have all my RBA/RTA's wrapped with a .5 coil (3mm silica or 1/8" ceramic Rope Wick).This is my sweet spot for vaping and it is a STELLAR,juicy flavorful vape in a Russian 91%.Make sure you make a slightly loose wrap at .5 (if you chain vape) or you will have problems with it not wicking fast enough.

Thanks really appreciate it
 
Status
Not open for further replies.

Users who are viewing this thread