Burning up attys at 6 volts

Status
Not open for further replies.

knifesideleft

Full Member
ECF Veteran
Sep 29, 2009
20
0
lowell Ma
So I just got my V3 literally 20 minutes ago and its been great since I moved up from the 901 and 510. However I just burned up the brand new atty and one of my older ones in a matter of 10 minutes. I still have about 5 left but this concerns be a bit. I hear that 4.5 ohms should bring this down to 5 volts. Does anyone have any good links to get some of these?

Also the atty heats up to the point where it would burn your mouth if you kept it on for more than 5 seconds, is that normal?

Any suggestions?
 

Houdini

Ultra Member
ECF Veteran
Jan 12, 2009
2,107
39
65
Las Vegas
It's normal for 6v to kill a standard atty. Try Nhaler. They have a huge selection of HV attys. I use the High Voltage 801 Atomizer w/ 4.5 Resistance. Been using the same one for 3 months. They don't get as hot either. I don't know how you're burning your mouth on the atty unless you stovepiping (not using a tip). With 6 v you shouldn't need to keep it on for 5 seconds. 2-3 should give you a good kick.
 

DonDaBoomVape

Reviewer / Blogger
ECF Veteran
Jun 5, 2009
3,353
598
79
South Florida
www.VapingGuides.com
...I hear that 4.5 ohms should bring this down to 5 volts...
You heard right. [NOTE: If you like, you can skip the following paragraphs in blue text. They are useful in understanding all this watts/amps/volts/ohms stuff, but not necessary to find a 4.5 ohm atomizer.]

It all has to do with Ohm's and Watts Laws:

ohms-watts_law.jpg

This looks more complicated than it actually is. You can just pick the formula you need for a particular purpose. For example:

Power (watts) = Volts X Volts / Resistance (ohms)​

Notice that an increase in battery voltage can be balanced by an increase in atomizer resistance. A 4.5 ohm atomizer on 6V will yield about the same power as a regular 510 atomizer on 5V.

To understand the burning up of atomizers, we turn to another formula, which considers the current running through the atomizer:

Current (amps) = Volts / Resistance (ohms)​

Atomizers are very delicate and can withstand only a modest current. Regular atomizers were designed to be used on 3.7V batteries (although the 510 battery is really only 3.2V). Increasing the voltage to 6V needs to be balanced by increasing the resistance of the atomizer.

[NOTE: Higher ohm atomizers are called "HV" (high voltage) because they are intended for use on higher voltage mods, but, in fact, they are high resistance.]
As Houdini indicated, NHaler sells a wide range of HV attys, both 4.5 ohm 510 atomizers and 4.5 ohm 901 atomizers.

NHaler also sells 5.2 ohm 510 attys. These are intended for use on 7V+, but can be used on 6V: not everyone likes a "5V" experience.

Many other suppliers sell "HV" atomizers. However, some don't specify the specific ohms of the atty. Those who do include IndyVaporShop (4.2~4.8 Ohms 510 and 4.7~4.9 Ohms 901), EastMall (4.5 ohm 510 and 901), Ecigsupply (3.9~4.5 Ohms 510), and VaporKings (4.4~4.6 Ohms 901). I encourage my fellow veterans to correct or expand on my explanation of watts/amps/volts/ohms stuff and/or provide additional sources.
 
Last edited:

Kent C

ECF Guru
ECF Veteran
Verified Member
Jun 12, 2009
26,547
60,051
NW Ohio US
I just burned up the brand new atty and one of my older ones in a matter of 10 minutes.

Any suggestions?

Study this:

http://img694.imageshack.us/img694/469/wattage.png

On the safe side stay in the 6-8W range and you won't have to pay attention other than noticing a loss of flavor and refilling/dripping. Some suggest 8-10W range but then you have to pay attention - no long drags and keep attys soaked.
 
Status
Not open for further replies.

Users who are viewing this thread