Talk about hot & wet... look at the size of that hole!
That is a very pretty atty. My concern would be the ss topcap/drip tip getting hot (& wet).
Catfish atty mods.
- Thread starter Chowderhead1972
- Start date
- th_trl_thread_readers 0
- Status
That is a very pretty atty. My concern would be the ss topcap/drip tip getting hot (& wet).
CH SX350J mod List
1. robbieblood
2. jhhollier
3. Hildicat
4. Houndb
5. Nautilusfan
6. TheDigital99
7. snakedoc
8. Eric Snyder
9. Finagle69
10. Chowderhead1972
Alternate
1. strongdad
2. inspects
3. BENTHOS
4. Calpis
5. Wongster360
6. lyspaere
7. Henry Etta
Just in case there will be more... I NEED a regulated squonker with that yihi chip.
1. robbieblood
2. jhhollier
3. Hildicat
4. Houndb
5. Nautilusfan
6. TheDigital99
7. snakedoc
8. Eric Snyder
9. Finagle69
10. Chowderhead1972
Alternate
1. strongdad
2. inspects
3. BENTHOS
4. Calpis
5. Wongster360
6. lyspaere
7. Henry Etta
Just in case there will be more... I NEED a regulated squonker with that yihi chip.
I've been away for a while... What is this CH mod you all have a list for? Is it that assault rifle mag one or something else?
- Pauly3
- Pauly3
I recieved the Manta V2 yesterday and built it this morning. 
First thing I did was measure the inner chamber @15mm and determined it was going to take a small atty build. So I put my 26g 12 wrap 1/16th ID dual coil nichrome setup in there.
On my next build the coils will be a little further away from the posts closer to the air. Or I might be able to just stretch them out a little.
Good flavor, lots of air, the AFC doesn't completely seal but close -Wide open to me seems like more air than the Marquis. A wider bore drip tip from my dark horse minimized the juice spit.
Overall, I think it's a keeper. A pocketable top fed air flavor atty.
First thing I did was measure the inner chamber @15mm and determined it was going to take a small atty build. So I put my 26g 12 wrap 1/16th ID dual coil nichrome setup in there.
On my next build the coils will be a little further away from the posts closer to the air. Or I might be able to just stretch them out a little.
Good flavor, lots of air, the AFC doesn't completely seal but close -Wide open to me seems like more air than the Marquis. A wider bore drip tip from my dark horse minimized the juice spit.
Overall, I think it's a keeper. A pocketable top fed air flavor atty.
Last edited:
Just got my black hellboy... Another great Atty by chowder.. Will build tonight and see how it compares to the first run of hellboys
18-8 Stainless Steel Machine Screw, Plain Finish, Cheese Head, Slotted Drive, Meets DIN 84, Right Hand Threads, Metric: Amazon.com: Industrial & Scientific
Screw replacement for the Rogue.. Works for the Manta also.
So the top cap has a built in drip top kinda like brads cap on the derringer? If so I'm ....ing stoked
PP and email sent for REMatty.
How you all feelin about this one? I asked about buying a 2nd one...because it looks like the flavor will be akin to the Derringer, it's small in size and, well, it just looks like it's up Sloth Alley to be perfectly honest...
How you all feelin about this one? I asked about buying a 2nd one...because it looks like the flavor will be akin to the Derringer, it's small in size and, well, it just looks like it's up Sloth Alley to be perfectly honest...
The RemAtty top reminds me of the Doppel Top I found for my Derringer
Bro, we are all waiting for this to be Sloth approved before buying multiples. You know how this works.
edit: Disclaimer - inswva may or may not be drinking Pappy Van Winkle this evening. Any posts from this account in the next six hours should be considered as compromised.
Looking forward to pics of you new Reo in a few days...Bro, we are all waiting for this to be Sloth approved before buying multiples. You know how this works.
edit: Disclaimer - inswva may or may not be drinking Pappy Van Winkle this evening. Any posts from this account in the next six hours should be considered as compromised.
It's little Friday!
I have plenty, so if you wish, by all means. In your analysis you missed the fact that these will have about a 2mm well so it will put out a much wetter vape if you keep it full. I only do wells intentionally on attys I know aren't going to leak. The veritas, the Marquis, the Raptor, and the RemAtty. If anyone else wants in feel free I ordered 60 of these and I will Shipp as many as you wish, the left overs will go to a group buy on Facebook. I'm sure I will need more but I have already gotten 50 more allocated.
Btw the cut off on getting off the Derringer list is midnight tomorrow night. After that you WILL catch a Ration of Shiitte for backing out. I am not above public humiliation, im actually pretty good at it so im told. You have been warned....
I'm going to take a break on new stuff after the Derringer run for my sanity and your wallets. During that break I will be working on my mod and shipping my overstock which at this point is massive. With the incoming order of hazes, bonsais,and more Mantas I have about $5k (my cost)just in clones. I will be around but unless the Haze goes platinum like the Manta, if so I will do another run of it. During my break I will be online a lot more and drilling a lot less.
I will keep Rogues, mantas, FSMs in stock I am well stocked on all of them once the next order arrives.
Tom I'm gonna paypal and e-mail you again for a 2nd REMatty. You rock. I have faith in this BEAST! Looks like the Derringer done better - and - I'm a Derringer freak, so...
Turk, please remove me from the Derringer list. I'm taking a 2nd REMatty instead.
Turk, please remove me from the Derringer list. I'm taking a 2nd REMatty instead.
- Status
