CE2 Fluxomizer Conversion kit

[ComaKid]

Has anybody used one of these?

I'm curious to see how well they work.

Can all the rings be pulled from a fluxomizer and replaced by the contents of the kit?

Thanks for any reply's.

 

[Rule62]

You remove all the rings and replace them with the new inner piece. Line up the slots with the wicks, and push down around the cup. The new mouthpiece is useless, unless you wrap a piece of teflon tape around it. They fit too loosely. Instead, I used the mouthpiece that comes one per 5 pack of Fluxos. The tube on the conversion insert still comes up into the hole.

 

[Caver]

I'm hoping the tube that sticks up from the insert will fit in the hole of a standard drip tip. If it will do that then I'm golden...

 

[vapspaz]

I'm hoping the tube that sticks up from the insert will fit in the hole of a standard drip tip. If it will do that then I'm golden...

It does.

 

[burns_erin]

I had to use a drip tip too. And the inner seal is frankly looser than I like.

 

[Rule62]

I tried them. I put them in a couple carts, and used the tip that comes in each pack of Fluxos. Frankly, I didn't care for them. I prefer using the "flip the donut ring" mod better. I felt the draw was a little tighter than I'm used to.

 

[robl45]

i've tried one so far, i'm not sure exactly what they are supposed to do, the one vision that I bought seems to work well, the conversion kit doesn't seem to do much. when I tried using it with the rubber tip the fluxos come with, it was juice in the mouth city same as without this new kit. now I shoved on the plastic tip, stuffed it in the tube so its tight, it seems better, but thats not a good solution, i'll try the teflon tape idea i suppose.

 

[ComaKid]

First of all, thanks everyone for posting your experiences.

Its very disappointing to hear these do not work as advertised. Was really hoping these would replace modding fluxos and make them easier to vape out of the box.

 

[zer0ith]

First of all, thanks everyone for posting your experiences.

Its very disappointing to hear these do not work as advertised. Was really hoping these would replace modding fluxos and make them easier to vape out of the box.

Just remember that bad did say that he wasn't happy with these but put them up because people were asking for them.

 

[harmonic]

and that he was going to have them resized again too

 

[ComaKid]

Just remember that bad did say that he wasn't happy with these but put them up because people were asking for them.

Thanks for the reply.

This kind of information should be available on the site. A customer shouldn't have to click through forum pages to find out that a product does not work as advertised.

 

[robl45]

i'm not sure what you guys are doing that are using other tips, its going to leak all over the place unless you stuffing the not so sealed seal from the plastic one into the bottom of the tip that you are using. i did that with the standard rubber tip that comes one per pack and tried it, was sucking juice all over the place even like that.

 

[vapspaz]

Rob - I tossed the whistle tip that came with the upgrade kit in a drawer and left the new cup seal inside my E2. I grabbed one of my delrin drip tips that I had ordered from GV a long time ago and pulled the o-ring off of it and it fits nice and tight into the E2. The length of this drip tip that slides into the E2 happens to be the perfect length and just contacts the top surface of the new cup seal. If it didn't I would have pulled the cup seal up slightly and then used the drip tip to "re-set" the cup seal thus making it the perfect hight. I'm not saying I can turn it upside down for 5 minutes without some juice leaking out but I can do the normal flip to re-wet the wick without any leaking. With that said however, I will get a mouth full if I vape while laying down with the PV pointing up. But then again I have enlarged the wick slots in the cup seal a little so they don't pinch the wick. I might have taken a little too much off. lol I've actually gotten to like the taste of my juice in the liquid form.

Hope this helps.

 

[robl45]

right, but the cup seal goes over the cup, is open on the sides so you can fill and has a rubber tube pointing up, unless you using the original seal from the plastic tip, if you tip the thing over, the juice is leaking out the sides of that cup seal and into your drip tip unless i'm misunderstanding what your doing.

 

[vapspaz]

The drip tip seals (covers) those "fill holes".

 

[robl45]

The drip tip seals (covers) those "fill holes".

ah, clearly we are talking about a different type of tip then, which one do you have, the standard drip tip on the site?

 

[vapspaz]

I have these. I've not compared the flange width to others that I have but I thought all drip tips where about the same dimensions in that area.

Clear Drip Tips in Various Colors SMOKEY CHARCOAL [gotvapes-cleardriptip-smoke] - $3.45 : GotVapes.com, E-cigarette Supplies - Atomizers Cartomizers Mods Juice and more

 

[robl45]

so on the xl cartomizers, these go all the way down to the cup seal?

 

[vapspaz]

Yup. If you see a little gap just pull the cup seal up a little and re seat the drip tip and let it push the cup seal back down. It'll put it at just the right height.


Edit: That is if these drip tips have not changes since I ordered them last year.

 

[burns_erin]

i'm not sure what you guys are doing that are using other tips, its going to leak all over the place unless you stuffing the not so sealed seal from the plastic one into the bottom of the tip that you are using. i did that with the standard rubber tip that comes one per pack and tried it, was sucking juice all over the place even like that.

Using the:

GotVapes REGULAR Chrome Pawn Style 510 Drip Tip

it does not leak with the vision style inner seal. It was definitely awkward for me to get it lined up, but it seems to get much better draw this way, and the wicks seem very happy. I will definitely look forward to the resized ones.