that 18490 is a fake, Sufie confirmed it with the vendor, FAKE. lol no surprise there
Cloupor Mini Mod 30W
- Thread starter Trailz
- Start date
- th_trl_thread_readers 0
- Status
Besides being better quality and probably safer, the Turnigy 1200mAh LiPo will far outlast any 18490. Let us know how it works for ya!
I ordered a SS one from here. Ad says available January 5th. Came to $21.00 and change, including shipping.
HD
I must have missed that ship date. Thanks for the clarification. It's still likely to show up faster than FT.
I completely agree. I'm not a fan of cheap, fake batteries so this, along with you guys, prompted me to install the Lipo sooner rather than later.
I soldered some wire to the battery with Deans micro plug connectors. I taped the ends with electrical tape (3M).
Make sure your pins are correct (battery side of the connector is female).
I had to figure out how the connector was going to sit so I made the wires lay along the battery.There's about a 6-8mm space in the battery compartment. I ended up using some plastic washers (not pictured) so the battery doesn't move around.
After putting the back on and shaking it a bit, there's no movement I can feel from the battery. It's charging now but I did take a few puffs from a KFL+ and it vapes fine up to about 20w (normally at 10.5w). I wanted to test it at a wattage higher than I normally would vape and it seems to work just fine. I'll let you guys know how long it lasts in a few days.
Depends on the tank, I guess. I'm going to assume my subtank will definitely overhang xD
i'm pretty sure if don't go over 22mm it'll be fine. almost positive I read it's 22mm in width...
Cloupor Mini 30W VV/VW Mode Box Mod for Sale
22mm x 36mm x 77.5mm. Half a mm overhang on both sides if the 510 if perfectly centered.
22mm x 36mm x 77.5mm. Half a mm overhang on both sides if the 510 if perfectly centered.
no overhang with a 22mm device. atleast, in the pic it shows a 22mm Atlantis sitting flush
I hope not but in the pics you will notice the 510 sits closer to the front edge than it does on both of the sides. So if its 22mm wide, a 22mm atty wont hang over the sides but since there is less space in the front I would think that it may hang a little bit over the front edge.
Those of you having the mini on the way do you happen to own an ipv mini as well? I'm eyeballing that the cloupor and waiting to see the new mvp before I make a decision on one.
I don't have either but the IPV mini isn't small at all. The MVP 20 is the same size as the old MVP. Phil B has a new video on the MVP. For me the Cloupor Mini is the one to get. If it is as nice as I think I will buy more than 1. Still waiting for them to ship..........
As I've said before, most of these new "Mini's" on the market aren't all that mini. They're trying to cash in on the popularity of the Istick's size which truly is mini. I've looked at the IPV and SX mini's and they're both about the size of the MVP2. I lost interest quickly because the IPV looked cheap and the SX was overpriced, IMO, on top of being oversized. There are many happy owners of both and you can talk to them in the corresponding threads.
http://www.e-cigarette-forum.com/forum/variable-voltage-apv-discussion/625973-ipv-mini.html
http://www.e-cigarette-forum.com/forum/variable-voltage-apv-discussion/617333-sxmini-mod-yihi.html
I think the Cloupor Mini looks way better in a simplistic design way. I like that it uses a 18650 and has magnets on the battery door. For the price (under $40) it was worth it for me to check it out.
http://www.e-cigarette-forum.com/forum/variable-voltage-apv-discussion/625973-ipv-mini.html
http://www.e-cigarette-forum.com/forum/variable-voltage-apv-discussion/617333-sxmini-mod-yihi.html
I think the Cloupor Mini looks way better in a simplistic design way. I like that it uses a 18650 and has magnets on the battery door. For the price (under $40) it was worth it for me to check it out.
I thought that way too but then I thought about it. Spring loaded may have problems too. What do you do if the spring breaks. Your done . I do like that you can adjust the 510 to you addy and never worry unless you change toppers.
I should have clarified. Not the new mvp 20. I'm talking the new mvp nobody has seen yet.
Like the other poster said, if your spring breaks, you're screwed. There's only a few attys that I've seen that have 510 threads that are way too long. Only 1 out of about 50 rdas/rtas htat I own has threads that are too long, and that's one of my Magma clones, and that's the only one that won't sit flush on anything.
I thought their 50w was supposed to be their "mini." Dang, my wallet hurts xD
- Status
