deedupdex builds! Variety in builds.
- Thread starter deedupdex
- Start date
- th_trl_thread_readers 0
- Status
Thank you guys for dropping by to check them out. I usually update once a week or every other week with a new build depending on my schedule. Once again thank you for the support. I do these builds for people to find enjoyment and to those who want to try them, I am here to help any way I can. Much appreciated!
~dex
Subbed for the one of a kind builds. Good stuff man
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Hey Guys I am near 9k followers on Instagram and I will be doing very big giveaway soon that includes building tool kits and juice to those who continue to support. Stay tuned and I will post up information how to enter for those who are not on Instagram! Thanks
Good job Dex... love the net type ...do you have any of a net in a cylinder shape ?..with maybe an eel swimming past lol
keep up the good work and posting of pics on here
im such a newb ...how do i even subscribe to a thread
keep up the good work and posting of pics on here
im such a newb ...how do i even subscribe to a thread
Good job Dex... love the net type ...do you have any of a net in a cylinder shape ?..with maybe an eel swimming past lol
keep up the good work and posting of pics on here
im such a newb ...how do i even subscribe to a thread
On the top of this thread, there is a bar that has "Link Back" Thread Tools" "Rate This Thread" "Display". Click on "Thread Tools" and the drop down should give you the option to subscribe to the thread. It will then take you to another option of how you want to receive the updates and how often. You can also "Rate This Thread" Hint:Excellent is what to rate it!!!
For you cloud chasers. Quad 26ga parallel with two pieces of wire 3/32 inside diameter "tweenpost" build. This originally had 3 parallel wires but came out way too low. I started by running both wires in the center posts. Attached two drill bits on each side of the posts. Ran the wire in "between" the posts routing it to the outsides of the negative posts into the the holes. These all use the post holes so you can clamp the wires and have it very strong without worrying about them moving around. The outer most wires do not short out because there is a stronger connection to the negative/circuit inside the post holes which the current will always take. Just make sure to pre torch the wires before building and pulse when test firing. If anyone needs help with this just hmu. But I do love this build. You can wick it two ways as shown on the top and bottom center of the picture. Don't miss out on the firing vid of this beast tommorrow. I will put it together tonight. Thanks for checking it out guys. <3
FIRE VID UP!
Firing clip of the "tweenpost" build. I've gotten tons of tags on IG and FB on people that had already built this. Thanks for trying it out. Keep In mind on some that I have seen done today try and keep the I.D (inside diameter) using a 3/32 bit. Not only will it have tons of clearance for the cap but I found it works alot better and you won't get hotspots. If you make it tall you will have to stuff too much cotton just to prevent hotspots and it wont burn well. I also saw some people doing twisted tweenpost. Just keep that diameter small for it to function properly. I would stick to untwisted to maximize wick and surface area contact. Anyway enjoy! Some of my followers are going to hate me but today go Sharks! & tomorrow go Giants! Lol
Click Image
Firing clip of the "tweenpost" build. I've gotten tons of tags on IG and FB on people that had already built this. Thanks for trying it out. Keep In mind on some that I have seen done today try and keep the I.D (inside diameter) using a 3/32 bit. Not only will it have tons of clearance for the cap but I found it works alot better and you won't get hotspots. If you make it tall you will have to stuff too much cotton just to prevent hotspots and it wont burn well. I also saw some people doing twisted tweenpost. Just keep that diameter small for it to function properly. I would stick to untwisted to maximize wick and surface area contact. Anyway enjoy! Some of my followers are going to hate me but today go Sharks! & tomorrow go Giants! Lol
Click Image
I saw your Instagram feed maybe a month ago after googling some build I was looking for. These are epic my friend; pure artwork and I'm not even talking about the Christmas tree build.
Sent from my SAMSUNG-SGH-I317 using Tapatalk
Sent from my SAMSUNG-SGH-I317 using Tapatalk
Last edited:
Thank you sir for your support. It's hard to get support from people who do not like to venture out into these types of builds. But you are much appreciated. What is your Instagram so I can follow back. Check back soon because I am having a 9K and a BIG 10K giveaway which includes all the tools I use to build!
~dex
Just an amazing build again Deep
To be honest, Im a little scared of running at the 0.12 ohm range, so I built this with a single 0.3mm wire over .094" diameter pins and came out to 0.46 ohms.
Its not the cloud chaser like your dual wire build, but fires nice and gives plenty of vape and flavor for me
Keep up the great ideas Bro, I look forward to your next build
Last edited:
Just an amazing build again Deep
To be honest, Im a little scared of running at the 0.12 ohm range, so I built this with a single 0.3mm wire over .094" diameter pins and came out to 0.46 ohms.
Its not the cloud chaser like your dual wire build, but fires nice and gives plenty of vape and flavor for me
Keep up the great ideas Bro, I look forward to your next build
Love it! nice build brotha! That's what it is all about! Making adjustments to your personal liking! Thank you for dropping by and trying it out! I have plenty to come!
I will have some fu with you! Thank you for checking them out. Stay in tune for more!
I will be doing vids soon you will def know it! And still working on your mount!!!
I will be here today Saturday 4/19 to do one on ones on builds for anyone in northern Cali. Come by and say hi!
- Status
Similar threads
