Different Atty resistances ??? your Personal favourite ??

[Satans_Hellhound]

For the last few Months I've been vaping on 2.4 Ohms Atties & found the general vapour & taste very good & satisfying .. I had occasion to swop out to a 2.0 Ohms atty the other day...... What a difference !!!! ....

vapour was down, taste was WAYYYY down & it just did not "Feel" right.......

The "vape Mail" arrived this morning with Mucho plenty 2.4's in ..... I'm a Happy Happy bunny again ...

Whats YOUR "favourite choice of atty/resistance" & Why .. what makes "IT" for you ?????

 

[Chikenbok]

Right now its probably a toss up between the Diver RBA and the kayfun, I usually run between 1.2-1.5ohms - nice warm vape, not too harsh, just right.

Edit: I almost strictly vape silica RBAs these days

 

[Rule62]

I use RBAs with ss mesh only. Depending on the juice, .8 to 1.0 ohms on mechanical mods. If I'm setting up for a vv/vw mod, above 1.2 ohms. Usually about 1.5.

 

[icyice]

Probably either the Igo W, Nimbus, or the RSST are my favorites.

I usually vape, sub ohm, at around 0.3-0.7 and the clouds and vapor production are insane! At first it may seem pretty harsh but after increasing my airflow holes I have gotten a much cooler vape. Also, because the vape is so dense, I found my self dropping my nic level. 12mg to 6mg right now.

 

[ZTKT]

As of right now I am frequently using my Trident RBAs.
Dual Coil at .14 ohms. Clouds of vapor with my vg juices. Majority of my juices are 0mg with a few at 6mg.

I aso run an IGO-L at about .8ohms which provides a better balance of flavor to vapor ratio.

I'm currently tinkering with my first Genesis style RBA using ss mesh and trying to figure out what's an ideal coil for it.

 

[kiryn]

Current favorite: Kayfun Lite & 3.1 running at 1.4 ohms.

Nice warm vapor with loads of flavor.

 

[ClippinWings]

0.8 to 0.9 on 28AWG Kanthal is IT for me... Epic vape

 

[Baditude]

2.0 ohm coils on AGA-T2s used on two Provari's, voltage varies by flavor used and taste.

2.5 - 3.0 ohm Ikenvape cartomizers in IBTanked cartotanks, used mostly on variable voltage mods, 3.4 - 4.8 volts depending on flavor selection.

2.0 ohm drip atomizer on a VMod-XL bottom feeder mod.

*I prefer a "cooler" vape. I no longer need my vaping devices to replicate an analog.

 

[dr g]

Resistance is not too meaningful per se. It's all about coil performance versus wicking, storage, etc. Different device designs perform differently.

That said my all-time favorite at this point is a 3.0 single coil carto tank. Smok udct. Hard to beat that reliability. Reliable production at 10-12w is a sweetspot for me.

I also like a mildly subohm coil (.8-1.0) in an octopus rda at 18-20w for volume vaping. My most recent "analog" was actually hookah so I do enjoy heavy volume.

BTW OP, simply changing from a 2.4 ohm to 2.0 ohm atty should not adversely affect vapor and flavor, unless you are hitting a limitation of the device, which is quite possible. what pv are you using?

 

[Alexander Mundy]

What he said, beat me to it.

Resistance is not too meaningful per se. It's all about coil performance versus wicking, storage, etc. Different device designs perform differently...........................................