Digiflavor Siren GTA

[Nailz]

Your welcome

Sometimes during their sales, it actually works out cheaper to use the 'MAP' code if active for the product.

 

[52anddone]

I was looking at your FT link, but can't find just where it fills at, as I see no fill screws on the bottom of the FT pic's.

 

[52anddone]

Citrus, banana and methol juices can cause some pc tanks to crack, so not recommended to use them type of juices in them.

I think that you can take Menthol off the list as possible tank crackers, as Menthol is about all I mix and vape. I have several PC tanks and run Menthol thru them every day, when starting with my first PC tank I asked several folks on here and they said that Menthol should be OK to use with a PC/PMMA tank, and I even went to Mt. Baker and found where they had a list of Tank crackers listed and Menthol was not on that list. Citrus, Spices (Cinnamon especially) are bad for PC/PMMA tanks though Nailz. You said Banana will also, I hadn't heard that that one did bad things either, but....

 

[52anddone]

I like a tight draw also hopefully you can see in the picture where I have it set, it's like half of the Sirens smallest hole.View attachment 660365

That Black Siren looks really good on top of your, what is that a Smok, anyways it looks like it was meant to be on there.

 

[Nailz]

I think that you can take Menthol off the list as possible tank crackers, as Menthol is about all I mix and vape. I have several PC tanks and run Menthol thru them every day, when starting with my first PC tank I asked several folks on here and they said that Menthol should be OK to use with a PC/PMMA tank, and I even went to Mt. Baker and found where they had a list of Tank crackers listed and Menthol was not on that list. Citrus, Spices (Cinnamon especially) are bad for PC/PMMA tanks though Nailz. You said Banana will also, I hadn't heard that that one did bad things either, but....

Yes I just checked and didn't see anything on Menthol, so I was wrong on that one, but banana I have heard a few times, and don't think it is as bad as say cinnamon juice, but banana is on Mt, Baker's list though - E-Juice Flavors That May Break a Plastic Tank - Mt Baker Vapor

 

[Nailz]

I was looking at your FT link, but can't find just where it fills at, as I see no fill screws on the bottom of the FT pic's.

The base unscrews and fill it up, bit like a taifun way of filling.

 

[52anddone]

Yes I just checked and didn't see anything on Menthol, so I was wrong on that one, but banana I have heard a few times, and don't think it is as bad as say cinnamon juice, but banana is on Mt, Baker's list though - E-Juice Flavors That May Break a Plastic Tank - Mt Baker Vapor

I see. I forgot that one (the banana), and surprised to see that on the list really.

The base unscrews and fill it up, bit like a taifun way of filling.

OK, that makes sense now. Thanks Nailz.

Yea, that cinnamon I have read is a real bad one for plastic tanks.

 

[Katdarling]

I see. I forgot that one (the banana), and surprised to see that on the list really.



OK, that makes sense now. Thanks Nailz.

Yea, that cinnamon I have read is a real bad one for plastic tanks.

And yet, I use it consistently, but again, I'm not quite sure on the meaning of PMMA tanks. I do know they are acrylic, but that's the extent of my 'expertise'.

 

[green.on.green]

Wow! That's fantastic! Thank you very much!!

Most welcome


Sent from my ONEPLUS A3003 using Tapatalk

 

[52anddone]

I do know that PC = Poly Carbonate, but PMMA = ??

 

[52anddone]

OK, here it is:

Poly(methyl methacrylate) (PMMA), also known as acrylic or acrylic glass as well as by the trade names Plexiglas, Acrylite, Lucite, and Perspex among several others (see below), is a transparent thermoplastic often used in sheet form as a lightweight or shatter-resistant alternative to glass. The same material can be utilised as a casting resin, in inks and coatings, and has many other uses.

 

[52anddone]

Polycarbonates (PC) are a group of thermoplastic polymers containing carbonate groups in their chemical structures. Polycarbonates used in engineering are strong, tough materials, and some grades are optically transparent. They are easily worked, molded, and thermoformed. Because of these properties, polycarbonates find many applications. Polycarbonates do not have a unique resin identification code (RIC) and are identified as "Other", 7 on the RIC list. Products made from polycarbonate can contain the precursor monomer bisphenol A (BPA).

 

[Katdarling]

Welp, aren't you just a wealth of! That's great, 5-2!

 

[52anddone]

Ultem
Ultem is a family of PEI products manufactured by SABIC as a result of acquiring the General Electric Plastics Division in 2007, developed by Joseph G. Wirth in the early 1980s. Ultem resins are used in medical and chemical instrumentation due to their heat resistance, solvent resistance and flame resistance. Ultem 1000 (standard, unfilled polyetherimide) has a high dielectric strength, inherent flame resistance, and extremely low smoke generation. Ultem has high mechanical properties and performs in continuous use to 340 °F (170 °C). Ultem 1000 has typical thermal conductivity of 0.22 W/(m·K) (but some sources give 0.122 W/(m.K)). It has "Questionable usage on alkaline solutions."[2]

 

[52anddone]

I'm just down to Copy & Paste right now, as forming complete sentences is a little tough right now.

 

[Katdarling]

forming complete sentences is a little tough

↑↑ My world, too.

 

[MoodyB]

Fast Tech doesn't have any replacement tanks for the Doggy, which is a bummer. The PC tanks I have vape just fine.

The SJMY Frosted tank also works fine with the SXK version of the Doggy RTA, if that's the version you have.

$2.45 SJMY Replacement PC Tank for Doggy RTA Atomizer at FastTech - Worldwide Free Shipping

 

[Bigbob2322]

I just finished doing the o-ring treatment on my Siren 25mm as well, but didn't think to document it with pic's. My Bad !

Edit: pic's would have come under the heading of Multi-tasking (doing more than 1 thing at once), and in that I am simply terrible at.



No problem bob, hope it helps ya out.

I did one today.

 

[JustWondering1]

The SJMY Frosted tank also works fine with the SXK version of the Doggy RTA, if that's the version you have.

$2.45 SJMY Replacement PC Tank for Doggy RTA Atomizer at FastTech - Worldwide Free Shipping

Thanks Moody!

 

[JustWondering1]

I did one today.View attachment 660921 View attachment 660921 View attachment 660923

Is the black thing I see around the airtube the o-ring you are using to stop the seepage? Is it working?