Drip set ups from canadian vendor
- Thread starter Jdasilva
- Start date
- th_trl_thread_readers 0
- Status
If you're set on buying from a Canadian vendor, Canvape has IGO-W2/3/4's. They are very popular models.
https://www.canvape.com/ProductDetails.asp?ProductCode=IGOW4
You would also need kanthal wire for the coil (also canvape) and I'd recommend cotton (from balls) as the wicking material. Micro screwdrivers (phillips and flathead), tweezers, scissors (or nail clippers), and a resistance checker or multimeter. You will also need good IMR batteries rated for high amps (preferable 20-30 amps) - canvape has a variety.
I would highly recommend building a microcoil setup and MOST IMPORTANTLY that you be fully conversant in battery safety and rebuildable issues (e.g., shorts) before you build a thing. Wouldn't want you to inadvertently build a pipe bomb, and I suggest you start your building career with >1 ohm coils.
Now, having said all that, you can order gear online from the US with no problems. Just keep the order to gear (not juice, to be safe with customs) and maybe get batteries somewhere else as they are considered a dangerous item by customs. I've had toppers and mods shipped from the US, the UK, Germany and China with no issues (and no duty or extra charges).
https://www.canvape.com/ProductDetails.asp?ProductCode=IGOW4
You would also need kanthal wire for the coil (also canvape) and I'd recommend cotton (from balls) as the wicking material. Micro screwdrivers (phillips and flathead), tweezers, scissors (or nail clippers), and a resistance checker or multimeter. You will also need good IMR batteries rated for high amps (preferable 20-30 amps) - canvape has a variety.
I would highly recommend building a microcoil setup and MOST IMPORTANTLY that you be fully conversant in battery safety and rebuildable issues (e.g., shorts) before you build a thing. Wouldn't want you to inadvertently build a pipe bomb, and I suggest you start your building career with >1 ohm coils.
Now, having said all that, you can order gear online from the US with no problems. Just keep the order to gear (not juice, to be safe with customs) and maybe get batteries somewhere else as they are considered a dangerous item by customs. I've had toppers and mods shipped from the US, the UK, Germany and China with no issues (and no duty or extra charges).
If you're not into building, or getting a larger mod (let alone a mechanical), just buy a few bridgeless 510 atomizers. Canvape has them for about six bucks each.
You might want to get a non-metal drip tip, too, they can get pretty hot since they're small.
You might want to get a non-metal drip tip, too, they can get pretty hot since they're small.
I've been using an IGO-L with a 1 ohm micro coil on my MVP and it's been working flawlessly. Drippers are nice since they are so easy to change flavors. I would also suggest 28 gauge Kanthal for the coil it's hard working with 32, and 28 is so much more solid.
If you build it with a coil with a resistance greater than, I believe, 1.2 ohm, it should fire fine. Will look a bit goofy, you'll want a beauty ring (if you've got a full-size Protank, the one that came with it should work fine).
Yeah but the MVP has a 3 amp limit, which means at 1 ohm you're never going to give it more than 3V, or 9W, which...not necessarily the best.
(if this is clicks and whistles, or Greek, to the OP, don't worry about it for now, but if you get an IGO and plan on using it on an Innokin mod maybe aim for 1.4-1.5 ohm if you can)
I think ill go with the IGO I started to rebuild a few of my kanger atomizers so rebuilding wont be a problem. I'll be using my itaste for now but will be looking into a mech mod in the near future.
Thanks all for tips and suggestions.
Thanks all for tips and suggestions.
- Status
Similar threads
