Dual coil RBA'S for Stock Reo?

[SLIPPY_EEL]

I'm just wondering which if any Dual coil rba's will fit on to a Stock Reo(un-milled version) ?

Just out of curiousity I tried my trident, it screwed in but didn't quite catch the pin, so I then decided to
tool up my rm2 with a dual coil and tbh I wasn't expecting much of a difference to a single coil at .7 ohms as the second
coil was set behind the post's without any air hole but I gotta say I was enjoying it a lot and had plenty of taste
and vapour on about .8 ohms (1600mah 30A).

I suppose I could try a 510 to 510 connection but don't really like the idea of the extra length, has anyone got any pic's?

Or if you guy's use dual coil's in your rm2's without any issue's, what way do you set up?

For me atm I gotta say more coil coverage is where it's at because although yeah I could wack a 6 wrap of 26g in on 1.5 or 2mm id
and get great taste, the cotton wick need's squonking after almost every hit, with 2 micros at sub ohm the juice for me doesn't seem
to disappear so quick

 

[Un5tab1e]

I ran one for a while. The first was set up regular next to the air hole and the second was turned with the wick end up directly in the middle.

Sent from my HTC6500LVW using Tapatalk

 

[Un5tab1e]

Sent from my HTC6500LVW using Tapatalk

 

[SLIPPY_EEL]

I ran one for a while. The first was set up regular next to the air hole and the second was turned with the wick end up directly in the middle.

Sent from my HTC6500LVW using Tapatalk

I found the cap getting very warm, that's why I went back to single, is that what you found?

 

[tmel]

When you do the dual coil like in that picture....do you put all 4 leads through the center post holes, or do you have to wrap the other 2 leads around the top of the screw?

 

[Filthy-Beast]

You can always drill a 2nd hole in the cap

 

[Un5tab1e]

I put them through the same 2 holes. Mine didn't seem to get too hot.

Sent from my HTC6500LVW using Tapatalk

 

[Raynman]

How about twisting two 28 gauge kanthal wires together and making one coil? It worked quite well for me. Sorry I have no pix that was a few coils ago.

 

[Commie]

This seems to work for me lately:

1. Fold your wire (28ga kanthal in my case) in half.
2. Twist about half inch of the folded end.
3. Coil one leg onto a drill bit in one direction, the other leg -- in the other direction.
4. Take out the drill bit, fold so it's two coils. But two drill bits through the parallel coils.
5. Twist the loose ends together. Now you have two twisted together legs, with parallel coils in the middle. Very sturdy, and easy to adjust, easy to secure in the atomizer without them shifting around.

All the way twisted wire works as well, but then the coil comes out too long and the ends don't get enough air. This setup seems to get all kinds of airflow.



Edit: Sorry if the coils look a bit crooked. Been vaping on this coil for about a week now, too lazy to straighten it out

 

[Un5tab1e]

This seems to work for me lately:

1. Fold your wire (28ga kanthal in my case) in half.
2. Twist about half inch of the folded end.
3. Coil one leg onto a drill bit in one direction, the other leg -- in the other direction.
4. Take out the drill bit, fold so it's two coils. But two drill bits through the parallel coils.
5. Twist the loose ends together. Now you have two twisted together legs, with parallel coils in the middle. Very sturdy, and easy to adjust, easy to secure in the atomizer without them shifting around.

All the way twisted wire works as well, but then the coil comes out too long and the ends don't get enough air. This setup seems to get all kinds of airflow.

View attachment 290496

Edit: Sorry if the coils look a bit crooked. Been vaping on this coil for about a week now, too lazy to straighten it out

I'll try this if my wire ever shows up. Supposed to have been here on the 30th and hasn't been scanned since the 27th. If these 2 coils go bad I'm screwed lol.

Sent from my HTC6500LVW using Tapatalk