eGo ONE tank series – CLR coil
- Thread starter pufZeppelin
- Start date
- th_trl_thread_readers 0
- Status
Yes dielectrical grease back in the day we used for the spark plug boots, i truly miss my 67 chevelle.
You never know who might go try it on the electrical threads!
For all you Ego One vapers — I was under the impression that the Ego Ones give good flavor with high VG eliquids. I am finding i get no flavor using the 1.0 ohm coil. I have tried several different flavors and they are all the same — tasteless of any flavor except the VG. I dropped down to a 50/50 eliquid and everything is tasting just fine. If anyone is vaping high VG (70% +) with good flavor, can you please let me know if you are using the 1.0 or 0.5 ohm or anything that you can doing. The Ego Ones will not go to waste though as I will use them for eliquids under 70% VG.
What coils? There are CL (blech!) And CLR (yum!) Then, if it's the CLR, there's the question of wick...
Sent from my SAMSUNG-SM-N910A using Tapatalk
•Noalox invented purpose is to stop aluminum wires from galling to non aluminum metals (High Voltage)
•Permatex® Dielectric Tune-Up Grease
Protects electrical connections and wiring from salt, dirt and corrosion.
Prevents voltage leakage around any electrical connection. Also prevents spark plugs from fusing to boots.
I use the Dielectric Grease mainly to stop dry threads/better threading and maybe to promote better electrical connectivity
I also apply it with a q-tip and then wipe it almost back off leaving just o-so-much
I use Vaseline to protect the battery terminals on my vehicles from corrosion
petroleum jelly probably works just as good as the other ↑ two ↑ for our purpose (vape mods)
Hey Friend! @NotSoMini - you sure it isn't the juice? Is it one particular juice or all your high vg ones? I have some high VG mixes that I can try out in an old Nautilus for example to see if there is a difference, but up to this point, I hadn't noticed that. I know *some* vendors add more flavor to high vg since PG is the flavor carrier, but if you are comparing side by side with a non Ego One tank, you would think both would taste the same. I am sorry you are not enjoying all your liquids in the Ego Ones!!! 
And you KNOW I will buy your old tanks and coils if you want to chuck 'em! DIBS!
And you KNOW I will buy your old tanks and coils if you want to chuck 'em! DIBS!
I use the CLR with rayon wicking and I use 80% to 100% VG exclusively and think I get marvelous flavor... 
(it all works for me)
(it all works for me)Thanks Nanny. I have tried several different flavors to make sure and they all had no taste other than the VG. I tried a couple of 70% and one 80% and they all had no flavor. These same flavors I have vaped in my Kabuki tank using the Nautilus 0.7 ohm coil and the flavor is definitely there. As mentioned they work fine with 50/50 so will use them for under 70% VG flavors.
I use the CLR with rayon wicking and I use 80% to 100% VG exclusively and think I get marvelous flavor...
Are you using the 1.0 or 0.5 CLR and at what wattage? I have even left the tank sitting overnight thinking they need a long priming.
I use fairly high VG (70/40) in my Ego One and Tron S. I've been vaping DIY Caramel and French Vanilla mixed at around 6%. Flavor is almost too strong.
Ga'roooooooon!
(you're cute, Shawn)
Had Gandy not posted the above, I would have unequivocally said that it was necessary to vape a higher PG vliquid.
Now, I'll just say that for YOUR taste, perhaps a higher PG vliquid is the ticket. :nodding: (<--- yes, I know that's not an emotical, duh.)
All day I waited for a groan. Thanks for being ga'rooooon up about itGa'roooooooon!
(you're cute, Shawn)
Had Gandy not posted the above, I would have unequivocally said that it was necessary to vape a higher PG vliquid.
Now, I'll just say that for YOUR taste, perhaps a higher PG vliquid is the ticket. :nodding: (<--- yes, I know that's not an emotical, duh.)
Sent from my SAMSUNG-SM-N910A using Tapatalk
OH!!!!!!!!!!! STOP!!!!!!!!!!!!!! 
I only build my own CLR's and I only use the big air hole center pin from the .5Ω coils
like to stay close to 1.0Ω (.75Ω - 1.25Ω) / using rayon / prefer a range of 9w-15w
I just lay a line of juice along the wick (priming) as I put it together
by the time the tank is assembled and installed on mod, it is ready to vape...
stock build coils, cotton is packed so tight it is about un-vapable
Nice! Guess I'm getting used to seeing those V2s. They look better all the time.I love the name Princess Penelope! Here's mine with her satin prince!
- Status
Similar threads
- Locked
