EHPro Bachelor RTA - single coil
- Thread starter Btsmokincat
- Start date
- th_trl_thread_readers 0
- Status
Been looking at this for a while since it was mentioned in the Rayon thread. Like my single coils. This looks like the best bet out there right now. Not perfect for what I would like but better than previous single coil tanks for sure. The serpent looks like a pain in the .... with offset backwards looking posts and the window issue.
Also, in my research, the tube tank rta on fasttech looks like a really nice single coil tank and I will have that on the way too.
Also, in my research, the tube tank rta on fasttech looks like a really nice single coil tank and I will have that on the way too.
I actually use a little coconut oil to lube all my o rings instead of ejuice. It tends to hold up better to quick rinses without having to be re applied until the next time I do a thorough soapy cleansing.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
The Tube RTA looks interesting just be careful with the positive block and 510 pin. It looks like the same setup as the fasttech kayfun monster clone that I had. The positive block was loose on mine and when I tightened the 510 screw it snapped the positive post with very little force.
The major draw for me on the tube are the reports that it's one of the quietest tanks. Did you find the air to be quite? I'm tired of noisy atties.
I only had the monster clone for a week when I broke it months ago. Sorry I don't remember if it was quiet but I do remember that it was a really nice vape. I was quite mad at myself for breaking it.
Monster is not quiet. Tube is extremely quiet. If you go thru the discussion section for the Tube, there are a lot of people fiddling with this one to give it more juice volume. They either use parts from an Orchid or parts from a KF4. I have my set up with the KF4 tank but am having some issues with it leaking. Still working on it.
Cool, Thanks to both for response. I'm ordering a bachelor now that it's back in stock at eciggity.
Yes I read that entire thread on the tube, I'm pretty much sold. Only bad thing is I don't have any of those tanks around but he gives the part numbers on ft. It would be great for when I need a quiet, unannoyying vape with good clouds.. Well, I should say my wife hates the whistle/ air noise more than I. But it is annoying.
Yes I read that entire thread on the tube, I'm pretty much sold. Only bad thing is I don't have any of those tanks around but he gives the part numbers on ft. It would be great for when I need a quiet, unannoyying vape with good clouds.. Well, I should say my wife hates the whistle/ air noise more than I. But it is annoying.
The Tube RTA looks interesting just be careful with the positive block and 510 pin. It looks like the same setup as the fasttech kayfun monster clone that I had. The positive block was loose on mine and when I tightened the 510 screw it snapped the positive post with very little force.
Makes me cringe seeing this. I'm determined to remain true to my Kayfun, etc. lessons and never buy another tank designed with air through the center pin. So far I've resisted temptation with Monster, Tube and others. So far so good.
Sure.. Tube styled RTA - 11.00 you can view Ft message threads on the product page. Specific thread is here on FT, just looks like a nice little tank to have around for the money, interchangeable with lots of different parts.
Only problem with the tube is that it really only holds about 2ml of juice rather than the 3.5ml that is stated. That is why there is so much talk about modifying it.
after vaping the bachelor for a couple days i have to give it a big thumbs up. i've only built on stm and goblin mini and the bachelor is easier than both. and i like the top fill. i did get a little leakage on my first build but was able to control it by closing the juice flow. i saw why when i emptied the tank, one side of the wick wasn't all the way to the bottom. i threw in a new coil and wick and have had only a tiny bit of leak from the connection to the mod it looks like. none from the air holes tho. next build i'm going to leave more room between the coil and edge of the deck so i can use a little more cotton in there. the tank fits well to my evic mini with no wobble like with the stm and seems to have a very solid electrical connection. i'm loving the great flavor and dense vape!
Got my Bachelor from eciggity today, damn that is one big ... coil they pre-install in it, didn't even try that one out, as wanted to go with my trusted clapton, also as want to use on black mods too, I switched out the orings for the black one's.
Was a little tight getting the wire down the holes, but a little wiggle and they went in, I admit took me 2 attempts, was getting jumping ohms on the 1st build, think I cut the legs a little short, 2nd attempt went well.
Wicking took me 2 attempts too, 1st try think I put way to much in, as was like sucking on a straw and ended up with some bad leaking, so 2nd attempt, put in a lot less cotton, and seems to working well right now, only got the juice flow half open and is wicking well so far.
Don't know if this is normal for how to wick, I did forget how it was done in the build video I watched, and as a new toy, just wanted it up and running, and so far is working really well, really good flavor.
It is good they supply different color orings, but wish they did include a extra top gasket too, already caught it once while closing it, luckily I didn't damage it, but if did, would of been stuffed.
I think the flavor is as good as my hurricanes that I really like, but the bachelor has top fill, so that is extra points for the bachelor, will see how it goes over the next week before jumping on another one
Was a little tight getting the wire down the holes, but a little wiggle and they went in, I admit took me 2 attempts, was getting jumping ohms on the 1st build, think I cut the legs a little short, 2nd attempt went well.
Wicking took me 2 attempts too, 1st try think I put way to much in, as was like sucking on a straw and ended up with some bad leaking, so 2nd attempt, put in a lot less cotton, and seems to working well right now, only got the juice flow half open and is wicking well so far.
Don't know if this is normal for how to wick, I did forget how it was done in the build video I watched, and as a new toy, just wanted it up and running, and so far is working really well, really good flavor.
It is good they supply different color orings, but wish they did include a extra top gasket too, already caught it once while closing it, luckily I didn't damage it, but if did, would of been stuffed.
I think the flavor is as good as my hurricanes that I really like, but the bachelor has top fill, so that is extra points for the bachelor, will see how it goes over the next week before jumping on another one
Glad it's working for you too. Nice fat Clapton.
But...
You swap out the blue and then put the tank on a blue mod with a blue drip tip.
What is with this large and vocal hate-on for the blue O-Rings?
We've had the ostentatious red on Kangers for a year and a half.
I've seen some out there colors from other brands.
I think one of my SMOK tanks has a set of other colored rings in the box.
WHY THE HATE-ON FOR THESE BLUE O-RINGS?
Color me confused.
But...
You swap out the blue and then put the tank on a blue mod with a blue drip tip.
What is with this large and vocal hate-on for the blue O-Rings?
We've had the ostentatious red on Kangers for a year and a half.
I've seen some out there colors from other brands.
I think one of my SMOK tanks has a set of other colored rings in the box.
WHY THE HATE-ON FOR THESE BLUE O-RINGS?
Color me confused.
Glad it's working for you too. Nice fat Clapton.
But...
You swap out the blue and then put the tank on a blue mod with a blue drip tip.
What is with this large and vocal hate-on for the blue O-Rings?
We've had the ostentatious red on Kangers for a year and a half.
I've seen some out there colors from other brands.
I think one of my SMOK tanks has a set of other colored rings in the box.
WHY THE HATE-ON FOR THESE BLUE O-RINGS?
Color me confused.
Well if you're a Kansas basketball fan.....and still remember that triple overtime loss to North Carolina in the tournament way .... way.....back when......then anything baby blue makes you want to upchuck....big time.
I have zero blue mods.
Red o rings look nice on my black or red mods
And Blue looks fine on Black or Silver.
Well if you're a Kansas basketball fan.....and still remember that triple overtime loss to North Carolina in the tournament way .... way.....back when......then anything baby blue makes you want to upchuck....big time.
Well... I'm not.
Aesthetics aside (I'm not a fan of Kanger mods) it's been just plain stupid "group think" how fast so many decided the blue O-rings were the product of the devil.
I'll just chalk it up to that... "group think".
And Blue looks fine on Black or Silver.
Well... I'm not.
Aesthetics aside (I'm not a fan of Kanger mods) it's been just plain stupid "group think" how fast so many decided the blue O-rings were the product of the devil.
I'll just chalk it up to that... "group think".
Sorry, just wasn't a fan of the blue. I like black and red. Just the way I was born.
- Status
Similar threads
