EHPRO Kayfun Lite Clone

[paladinx]

I just ordered one of these from another site.. it came to 51 dollars with a bottle of juice and shipping. I enjoy cartos.. I like the juicy wet kind of vapor you get from a good carto in a tank. I was going to get the russian 91 percent, but no one seems to have it so I got this. After reading this thread .. Im not sure I am going to like it now. i might just return the thing when I get it. i don't do lung inhales or anything like that so I don't like airy draws.

what do you guys think? Someone who is looking for something that performs like a carto.. Do you think I should just return it and wait for the russian 91.. or keep it and tinker with it till it works ?

regards

 

[Bern Diesel]

Well, people that go from genny's to KFL's generally say the draw is too tight. So in that sense, it may be closer to a carto. Taste and vape production are definately better as well. Personally, if the draw on this is more airy than a KFL, I will like it

 

[Matthew Keller]

Honestly it's not bad if you are a little handy. Just did the airholes, and actually got some screws that fit and it's great!

Sent from my VS870 4G using Tapatalk now Free

 

[ektouge]

What site did you guys get it from?

 

[Matthew Keller]

Discountvapers.com

Sent from my VS870 4G using Tapatalk now Free

 

[thomasjames0]

Man, I don't deny the tight draw you guys are talking about at all but the one I have is far from tight. Weird, but despite the draw I have on mine I really do like this clone a lot. I find myself vaping a lil less cause its giving me a nic rush with 12mg juice.

 

[kanga]

sooo I had a crazzy tight draw on mine... I took the airhole screw thing out, stuck a paper clip in it and took out a lot of plastic crap stuck in the air screw thing... hope this helps anyone

 

[wsteven321]

i opted to get the ehpro 3.1 instead of the lite in a group buy, and now im thinking that was a really good choice. AFC looks like its gonna be very useful.

also, with the stock screws would ribbon wire be possible? 0.8mm more specifically.

 

[Matthew Keller]

Well I found much better screws at radio shack, the size is 1.6mm machine screw. Got some with wider heads.

Sent from my VS870 4G using Tapatalk now Free

 

[kanga]

Any other sites selling this? I want to get another one and DiscountVapers is out of stock

 

[vapdivrr]

Right now my only complaint is the small screw heads. The threads were pretty crunchy in the beginning. But now after playing around with it for a while they are pretty smooth. The airy draw I got used to. The vape is very warm with the airy draw....if the draw was much tighter it would be down right hot. Since I use 28g wire I have hard time catching the wire with these ridiculously small screws. If anyone finds good replacement screws please let us know.

I figured maybe we are doing this all wrong and the screws were meant to go into the side holes of the deck. I tried this and it worked like a dream...very easy set up. Basically the wires go through the top of the deck and when you tighten the screw from the sides they catch the wire. But there was one big problem.... the chimney wouldn't fit back on if you inserted the screws from the side. SO that idea went down the drain...lol. I don't get what those side holes are for.

maybe the extra holes could be for dual coils? not really sure. I guess one could make another coil mounted there and bend it up over the airhole next to the top coil?

 

[Topper]

Not possible actually - screws on other threads (not on top) will make short to chimney. And I on my Kayfun 3.1 can't even screw d chimney on it place! Sadly....
But anyway it's possible to make dual coil setup:

 

[thomasjames0]

That looks beautiful topper! What is the resistance at?

 

[b00gym4n]

Can someone post a picture of their KFL clone drilled? I want to drill mine 1/16, but I don't want to mess up.

 

[Topper]

That looks beautiful topper! What is the resistance at?

Kanthal 0.30/12 warps per coil
dual microcoil - resistance become 0.9Ohm
cotton for wick

 

[pizza2me]

Has a anybody with less then perfect threads tried putting noalox (sp?) On threads?

 

[thomasjames0]

I have not tried pizza but i think i will give it a shot cause mine are bad!

 

[Matthew Keller]

My threads after a good washing of the device are smooth. I really love this thing.

Sent from my VS870 4G using Tapatalk now Free

 

[gomjabbar]

I wouldnt put noalox on threads...this stuff goes into your lungs. a mech mod is one thing but not an atomizer.

 

[gomjabbar]

I just picked up M1.6 machine screws from ace hardware and its much nicer to work with now.