Just be careful with the glass. I just cracked mine last night by tightening it a little too much.
Ehpro Mini Buddha HELP
- Thread starter VapinAngel
- Start date
- th_trl_thread_readers 0
- Status
Just be careful with the glass. I just cracked mine last night by tightening it a little too much.
I was using 50/50 but went to 70/30 with this tank. I also was able to cut the nicotine back from 18mg to 8. I haven't made it to 6mg yet lol.
Going from 18 to 8mg is a drop of greater than 50%. For me, I think I got the same flavors in a 12mg and mixed them with the 18 to get 15mg juice. I bought juice in groups, each group was a step down in the same manner.
You should get a medal for courage...like that movie lion.
You should get a medal for courage...like that movie lion.
The lack of replacement glass is the only thing I really don't like about this atty. Gearbest briefly offered them, but they did not last long, and according to what the CSR told me they won't be restocked. Might be able to get IBT to cut some customs, but that is a costly alternative.
I've never filled mine from the bottom, yeah I know the chimney usually won't cooperate and comes unscrewed at the base. I only fill it when empty so it only takes a second to remove the cap from the chimney.
Definitely agree on the "be careful with the glass" comment. IF, or rather when I eventually break the glass I'll be cutting about 2mm off the base of the chamber. The tank is the same diameter as the Taifun GS, the GS tank is unfortunately a couple mm to short.
I've looked closely at the chamber, should be doable. not difficult to remove the needed 2mm off the bottom. Bad part is it will slightly reduce capacity. Good thing is I have a few steel tanks, and nearly 70 Plastic spares once I do this.
A very good alternative to this atomizer is the Flash-E VS. The FEV VS is about the same size, vapes quite nicely, builds easily, only caveat is it is not as sleek looking.
FEV-VS
I've never filled mine from the bottom, yeah I know the chimney usually won't cooperate and comes unscrewed at the base. I only fill it when empty so it only takes a second to remove the cap from the chimney.
Definitely agree on the "be careful with the glass" comment. IF, or rather when I eventually break the glass I'll be cutting about 2mm off the base of the chamber. The tank is the same diameter as the Taifun GS, the GS tank is unfortunately a couple mm to short.
I've looked closely at the chamber, should be doable. not difficult to remove the needed 2mm off the bottom. Bad part is it will slightly reduce capacity. Good thing is I have a few steel tanks, and nearly 70 Plastic spares once I do this.
A very good alternative to this atomizer is the Flash-E VS. The FEV VS is about the same size, vapes quite nicely, builds easily, only caveat is it is not as sleek looking.
FEV-VS
Going from 18 to 8mg is a drop of greater than 50%. For me, I think I got the same flavors in a 12mg and mixed them with the 18 to get 15mg juice. I bought juice in groups, each group was a step down in the same manner.
You should get a medal for courage...like that movie lion.
Well that certainly explains why I killed two people....lol
The lack of replacement glass is the only thing I really don't like about this atty. Gearbest briefly offered them, but they did not last long, and according to what the CSR told me they won't be restocked. Might be able to get IBT to cut some customs, but that is a costly alternative.
I've never filled mine from the bottom, yeah I know the chimney usually won't cooperate and comes unscrewed at the base. I only fill it when empty so it only takes a second to remove the cap from the chimney.
Definitely agree on the "be careful with the glass" comment. IF, or rather when I eventually break the glass I'll be cutting about 2mm off the base of the chamber. The tank is the same diameter as the Taifun GS, the GS tank is unfortunately a couple mm to short.
I've looked closely at the chamber, should be doable. not difficult to remove the needed 2mm off the bottom. Bad part is it will slightly reduce capacity. Good thing is I have a few steel tanks, and nearly 70 Plastic spares once I do this.
A very good alternative to this atomizer is the Flash-E VS. The FEV VS is about the same size, vapes quite nicely, builds easily, only caveat is it is not as sleek looking.
FEV-VS
How is the FEV-VS for refilling?
Yes Kayfuns cab be interesting to fill.Uh oh, lol!
I guess you haven't had a kayfun lite
Simple. Unscrew the tank, turn upside down and fill up the the chimney stem. You can use any kind of bottle.
So basically you're saying that a semi slow person with eyes going in opposite directions can fill this one? Because that is exactly what I need!!
I've never had any trouble filling a kayfun . I actually have one again, a Monster v3 and I'm enjoying it.
. I actually have one again, a Monster v3 and I'm enjoying it.
Multiple ways to fill the various Kayfuns, none are all that difficult. Are you wanting to stay with the approximate footprint of the Buddha, or a 22mm atomizer?
You don't know what you're missing.
Kayfuns have the fill port on the bottom.
With most you have to dump the juicd to work on the build.
Kayfun has issues with temp control.
Trapping the leads under screw heads.
Single coil only.
There are some pros.
Good flavor
Easy to build on.
You can have all kinds of options.
Kayfun Lite + base MTL ONLY.
Doyble drilled base for more airflow
Kayfun Monster for mouth to lung.
If you want a stealth vape you can have a super short atty that us only 30/mm tall not counting 510 and drip tip and hold 2.5 ml. One person put a bell cap on top of the M tank and had a Kayfun about as long as an 18650 that held almost 8 ml of juice.
Fasttech sells top caps where you can top fill the Kayfun.
Kayfuns are known for better than average flavor because of the chimney.
You should look at all of the options for tweaking the Kayfun at fasttech.
I've never had any trouble filling a kayfun
The first Kayfun that I really enjoyed. The only thing I would change is put some post holes in it.
- Status
