eVic setup and photos

[evgeny131]

cant post pics for some stupid reason....in my album theres a black evic i actually like it...it pushes 1.1ohm coils...havent tried 1 ohm i think thats where it stops...

 

[evgeny131]

http://www.e-cigarette-forum.com/fo...ng-vamo-zen-sw-innokin-svd-evic-black-bod.jpg

 

[evgeny131]

finally i managed to link to my black evic
check out link above....

 

[evgeny131]

heres a pic of my evic i love this thing more and more cuz it pushes 1 ohm coils just found out....

 

[evgeny131]

here is the pic...lol still having trouble uploading ...

 

[ChadGio]

Getting the black sleeve tomorrow

 

[Jeremy Evans]

View attachment 213213 heres a pic of my evic i love this thing more and more cuz it pushes 1 ohm coils just found out....

I can make mine push a .9 ohm coil. its is .8 it doesnt like.

 

[SuperDave68]

i got mine around mid feb, it's rev 1 without the screw support. so far everything is good, and i have had a couple of drops, one fairly nasty out of my coat pocket at the airport.

I am running an AGA/t2, modded for a cotton U-Wick, .1x .5 ribbon kanthal, 1.5 Ohm coil (pics are in my profile)

i love the evic

 

[bwxdme]

I can make mine push a .9 ohm coil. its is .8 it doesnt like.

How'd you get it to push that low. I thought 1.2 was the limit. I vape at 8watts, I don't think the evic is strong enough to push at that low of resistance . Lemme know guys cause that'd be awesome.


Sent from my iPad using Tapatalk HD

 

[bwxdme]

Well this is mine with my new brushed finished Siam mod tubes. I'm loving it right now

Sent from my iPad using Tapatalk HD

 

[JuniorNA]

Here's mine

 

[InterFace]

 

[t.d]

Where's everyone getting their 18350 tubes? I really wanna get an official JT silver 18350 tube... and flat cap when its released.

 

[DaxFX]

Where's everyone getting their 18350 tubes? I really wanna get an official JT silver 18350 tube... and flat cap when its released.

The eGo-T fits and the anyvape cvi.. So far forw hat i have research those are the only 2, no original evic 18350 yet


Sent from my iVap using Tapatalk HD

 

[StereoDreamer]

Mhm! I have multiple tubes but this i the way it sits most of the time!

View attachment 212805

View attachment 212806

Hey, I thought I was the only person who put o-rings around the tube of my mods. I have them on my eVic, AcryliMax, Silver Bullet, and even on my eGo Twist. I do it for two reasons:

1) the o-rings in the middle have a lanyard loop on them so I can wear them on a lanyard, and
2) they protect the mods if they get knocked over on a table.

 

[Marredding]

That's a nice set up. Great idea with the Orings. I am always knocking my Evic over.

 

[Jeremy Evans]

How'd you get it to push that low. I thought 1.2 was the limit. I vape at 8watts, I don't think the evic is strong enough to push at that low of resistance . Lemme know guys cause that'd be awesome.


Sent from my iPad using Tapatalk HD

luck I suppose. It took a bit of playing around with though. I made a small coil and for interest of science didnt cut the neg tail and just steadily walked it out til it didnt say atomizer short.

 

[shihchuansun]

Vapemail delivered some new hats for my EVIC. Quicky photo shoot with 18650, 18350 and with RSST on top. Enjoy!

 

[DaxFX]

Well this is mine with my new brushed finished Siam mod tubes. I'm loving it right now

Sent from my iPad using Tapatalk HD

I liked that brushed,,, how much you paid? And were?


Sent from my iVap using Tapatalk HD

 

[RickCain]

Here is mine in 18500 mode. Really wanting a 18350 tube now...