Evolv-ing Thread

[TrollDragon]

Looks like there is a silicon gasget just under the rim? Can you remove it?

The exocet clone is short An authentic is rare as hens teeth! Its the unicorn of the BB world

There is no silicone, it's all bare metal. That pic was hoisted from the net and zoomed just to show the size/o-ring.

 

[Steamer861]

There is no silicone, it's all bare metal. That pic was hoisted from the net and zoomed just to show the size/o-ring.

Thats too bad I feel your missing out on the Exocet! Maybe you can find a BB key some wear?

 

[TrollDragon]

Thats too bad I feel your missing out on the Exocet! Maybe you can find a BB key some wear?

I just need to extend the 510 part of it a little and it should be fine. Still loving the EUC coils at the moment.

 

[Steamer861]

I'm running one EUC coil in power boost mode @35 watts, it boost's up to 45 or 50 for a second then down to 35 I find it performs way better that way, than in TC on 316L setting. In SS TC it was some what anemic
The other two are both on the Exocet's In TC on Ti

 

[dwcraig1]

Now what?
https://www.washingtonpost.com/heal...er-fees/?noredirect=on&utm_term=.f51cfe5b4aea

 

[dwcraig1]

EUC coils, I had to look it up......LOL

 

[BillW50]

Yes, I've seen that dwcraig1. Very disappointing.

 

[BillW50]

EUC coils, I had to look it up......LOL

You need the A Tank and the adapter to run EUC on the BB.

A-Tank $9.90
$8.37 Replacement Accessory Set for SXK BB 60W Mod Kit - 5ml / POM at FastTech - Worldwide Free Shipping

Vaporesso Ceramic EUC Coil Head w/Adapter (5-Pack) $8.08
EUC Adapter and ceramic coils
$8.79 Authentic Vaporesso Ceramic EUC Coil Head (5-Pack) 5-pack - 316L stainless steel / 0.5ohm (25-35W) / w/ sleeve at FastTech - Worldwide Free Shipping

 

[Steamer861]

Now what?
https://www.washingtonpost.com/heal...er-fees/?noredirect=on&utm_term=.f51cfe5b4aea

It was just a matter of time before the FDA came looking for the $ it's loosing from BT!!

 

[BillW50]

 

[laurie9300]

They're the same Bill Like I'v said before, If you don't open the BB, you cant tell it apart from the clone!

My sxk is a different thread from my authentics.

 

[BillW50]

My sxk is a different thread from my authentics.

Is yours a newer SXK or older? Older SXK also had the polarity of the magnets different, so the panels wouldn't swap.

 

[dwcraig1]

Well my Vapecige box couldn't handle work, leaking but where the tube comes through the case but still the 510 no doubt.

 

[dwcraig1]

 

[BillW50]

 

[tiburonfirst]

 

[laurie9300]

Is yours a newer SXK or older? Older SXK also had the polarity of the magnets different, so the panels wouldn't swap.

Not sure, but authentic panels fit, but authentic threaded tips and 510s don't fit the sxk.

 

[dwcraig1]

While this may not be the plan it won't surprise me if I pull the board out of the Vapecige and install it in my SXK Boxer.

 

[dwcraig1]

First off, not my picture. Unlike the SXK Boxer the board on the Vapecige VTX is mounted on the back side of the battery sled.
To be able to unsolder the 510 wiring requires removing the board first.

 

[dwcraig1]

I'll know better after I get home but there's a good chance the the innards from the Modmaker 510 will screw into the Vapecige's 510 housing, but perhaps not to the correct depth/distance.