Evolv-ing Thread

[awsum140]

I never dry burn, can't get that burned taste out until after a tank or so. Much easier to just replace and go. I use SS40 already with TC and it works way better tan 316L, at least for me. Ti could be dry burned if it's done carefully and you don't take it to brighter shades of red, say a 25 using the "Fifty Shades of Grey" scale. The trick being not to over oxidize the surface.

 

[Steamer861]

I glow the Nicrome & Kanthol red hot, don't seem to do any thing to them
For the Ti round wire I just remove the coil straighten it with a drill & wipe the wire clean
The Ti Claptons, nothing works I just replace them when they get to gunked up.

 

[mikepetro]

 

[TrollDragon]

I'm surprised you got the Pulse BF'er? I didn't like the switch or the locking mec
They both have voltage drop written all over them.
I went with the "Squeezer" I'm real happy with it $24 from FT, with extras

I picked it up for S&G's when I grabbed some BB vape accessories. It was the Pulse or the Nudge and I didn't like the look of the Nudge. I think it will be much better with some Ni80 coils, I have a pair of 22ga KA1's in the Peerless now @0.17Ω and it's vapeable.

If I can find a build that is acceptable in the Pulse, I might just look into getting a Squeezer.

 

[mikepetro]

Ugggggh, its an invasion...............

 

[Steamer861]

Ugggggh, its an invasion...............

Shouldn't you be doing some thing? A list or some thing?

 

[mikepetro]

Shouldn't you be doing some thing? A list or some thing?

In a few minutes I will be removing something......

She is almost here!

 

[Steamer861]

I picked it up for S&G's when I grabbed some BB Vape accessories. It was the Pulse or the Nudge and I didn't like the look of the Nudge. I think it will be much better with some Ni80 coils, I have a pair of 22ga KA1's in the Peerless now @0.17Ω and it's vapeable.

If I can find a build that is acceptable in the Pulse, I might just look into getting a Squeezer.

The NI80 coils I posted, ohm out @ about .2 ish with duals I have 2 in a +, it blows clouds I bet a single would work good on the Pluse BF'er?
I run a .19 Fused Kanthol Clapton on my Squeezer with a Pulse 22, I have this wicked "Fuji Apple" juice in there it's a Sweet setup

 

[Alexander Mundy]

Ugggggh, its an invasion...............

 

[awsum140]

View attachment 718843

Is that Steamer's new rig?

 

[TrollDragon]

The NI80 coils I posted, ohm out @ about .2 ish with duals I have 2 in a +, it blows clouds I bet a single would work good on the Pluse BF'er?
I run a .19 Fused Kanthol Clapton on my Squeezer with a Pulse 22, I have this wicked "Fuji Apple" juice in there it's a Sweet setup

I have dual AVS SS316L triple core fused in one + and dual 22ga KA1 in another, both at 5mm.

I got these free with the Boaz RDA from AVS, way too much coil for the Boaz but not for the Plus or Titan. I put a single one in the Pulse 22 taking off 2 wraps, still too much for the Pulse BF but not for the Drone.
10 Pack Framed Staple Coil 316L SS (28*2/.1x.4*6/38g)

 

[TrollDragon]

Is that Steamer's new rig?

Reminds me of the Triton from Dark Ronin Mods back in the day.

 

[SlickWilly]

Aghhh..... my mother in law is here again.....

 

[kiba]

Thanks for the heads up
I'v been wanting to try SS430 for a while now, it was hard to resist premade SS430 Claptons from AVS
So whats the TCR for SS 430 on a DNA?

Idk I just use a TFR map from se, but I used my own temp thingys rather than se's (I think -100, 0, 70, 200, 400, 600, 800), theirs start at - 50, and all of evolv's start at -100, probably just an ocd thing but why screw with what works.

But mine have been acting all wonky today after 2 days of use, what are the correct size grubs to order from that site?

Sent from my SM-G955U using Tapatalk

 

[ShamrockPat]

I picked it up for S&G's when I grabbed some BB Vape accessories.

Oh no, do you know Albert? Then I noticed it's 3 Canadians, who let us in? Whitby here. @TrollDragon where in NS? I've been known to visit Timberlea too often.

 

[SlickWilly]

Idk I just use a TFR map from se, but I used my own temp thingys rather than se's (I think -100, 0, 70, 200, 400, 600, 800), theirs start at - 50, and all of evolv's start at -100, probably just an ocd thing but why screw with what works.

But mine have been acting all wonky today after 2 days of use, what are the correct size grubs to order from that site?

Sent from my SM-G955U using Tapatalk

Sorry, I forgot to come back and reply to you yesterday, not sure what size your atty uses but I can tell you the Steam Crave Aromamizer V1 & V2 and the Merlin's use M2.5 x .45 x 3 long set screws --> M2.5 x .45 Socket Set Screw Cup Point Metric A2 Stainless Steel They seem to be pretty common.

 

[kiba]

Keeps reading "ohms too high" what's that about? Coil is about .6Ω cold

Sorry, I forgot to come back and reply to you yesterday, not sure what size your atty uses but I can tell you the Steam Crave Aromamizer V1 & V2 and the Merlin's use M2.5 x .45 x 3 long set screws --> M2.5 x .45 Socket Set Screw Cup Point Metric A2 Stainless Steel They seem to be pretty common.

It's the single coil deck for Supreme v2

Sent from my SM-G955U using Tapatalk

 

[SlickWilly]

Keeps reading "ohms too high" what's that about? Coil is about .6Ω cold



It's the single coil deck for Supreme v2

Sent from my SM-G955U using Tapatalk

Can't help with the "ohms too high" but I'm sure one of the gang knows.

Steamer or Mike can probably tell us if the Supreme V2 single coil deck uses the same grub screws as the mizer V1 & V2 dual post decks, if it does then those I posted will work.

 

[Steamer861]

@Troll

Can't help with the "ohms too high" but I'm sure one of the gang knows.

Steamer or Mike can probably tell us if the Supreme V2 single coil deck uses the same grub screws as the mizer V1 & V2 dual post decks, if it does then those I posted will work.

Willy, there the same set screw you sent me, just a bit longer.(2mm)
the threading & head are identical

 

[ShamrockPat]

Keeps reading "ohms too high" what's that about? Coil is about .6Ω cold

(On a DNA mod) The watts you're trying to use are too high for the output voltage, so they're being throttled down