Evolv-ing Thread

[SlickWilly]

Replaceable battery If I'm going out for the day & would rather a stealthy mod I can bring a spare battery instead of the ERM+

Good morning

Hotcig could just use the DX200 front half for the board and make a single 18650 back half. They already make a dual 18650 for the DX200

 

[tiburonfirst]

 

[Steamer861]

The Hot cig mod is nice The ERM is small 75 watts is more than enough for my ADV, and 2 18650 will last me the day no problem, even long summer work days Now when I'm working I bring the 1300mAH mods cause I can get the whole day out of a charge. The new 75 watt ERM will give me an option I didn't have before My 900mAH ERM's don't go to work cause they would run out of charge in the late afternoon

 

[Tpat591]

I actually started playing with the ERM because I am partly thinking of using the control panel contours in some other designs. The way the 1/2s of the the case fit inside each other it sort of does a certain amount of pinning as well.

 

[mikepetro]

I actually started playing with the ERM because I am partly thinking of using the control panel contours in some other designs. The way the 1/2s of the the case fit inside each other it sort of does a certain amount of pinning as well.

That tongue and groove setup is a pain to mill though.

 

[mikepetro]

Look what was on FB......

 

[KTMRider]

Look what was on FB......

View attachment 546603

The only feature I'd like to see is an auto-rotating screen like on the SX350j. That is the only feature I like about the Yihi chip.

I have led buttons on all my Vaporsharks and it was a novelty with my first one. The DNA200's led lights up when charging but it's so dim that it's pretty much useless except in a dark room.

 

[Pdizzle]

Haven't read through all the pages. Has it been leaked that the 75w is the exact same footprint as the 200? Button position and Everything? Working on a stabwood box to prepare for the release or a Mike Co op

 

[mikepetro]

"For me" LEDs are a gimmick. A lot of mods are out there where the fire button lights up or whatever, but what usefulness does it actually serve - other than "purdy".

 

[berger]

gives you confirmation you pushed the button

 

[SlickWilly]

Early on in the Evolv forum there was a thread on how to hook up an led button via the board. I think it was James (?) that instructed those asking where to solder on the board for it to work.

ETA: If my memory serves me right, sometimes it doesn't.

 

[SlickWilly]

Yup, there was chat about it
Could you check my build out? - DNA 200 Early Adopters Forum

LED Button Help? - DNA 200 Early Adopters Forum

 

[awsum140]

To me an LED fire button is kind of like a 180 degree forward looking camera in a car or truck. If you've got to look at a display on the dashboard to see what's in front of you, maybe you shouldn't be behind the wheel.

 

[Steamer861]

The only feature I'd like to see is an auto-rotating screen like on the SX350j. That is the only feature I like about the Yihi chip.

I turned that off on mine, to be honest it bugs me.
I got both my "j" chips working perfectly I had to turn down the TC to 345 degrees not to burn my cotton. I really like the soild ohms lock I can set it at an ohms reading and it stays there The battery life Sucks, I'm sure it will be better on the dual 18650 Q chip mod I preordered I'm becoming a closet Yihi Fan Boy

"For me" LEDs are a gimmick. A lot of mods are out there where the fire button lights up or whatever, but what usefulness does it actually serve - other than "purdy".

Fluff

 

[Steamer861]

So Mike it's been a few days with the Supreme, You haven't really said much Hows the flavour?
Any Cons you discovered so far? does the juice control work good, can you top fill with no leaks/flooding of the chamber? Are those little pins a PIA? We all want to know

 

[mikepetro]

So Mike it's been a few days with the Supreme, You haven't really said much Hows the flavour?
Any Cons you discovered so far? does the juice control work good, can you top fill with no leaks/flooding of the chamber? Are those little pins a PIA? We all want to know

To be honest, I have been so busy with other endeavors I havent messed with since the hot spots. I brought the second one to work with me today in hopes I might sneak in a minute or two to build it out, but no such luck. Between normal work headaches, I also have been having to research flights and hotels etc to Slovakia. Vienna is the connection point and I have been trying to see if there is enough attraction to the place to burn up a vacation day while I am there.

Anyway, havent touched it since the other night, maybe tonight.

 

[Steamer861]

DNA200 mod 1600mAH battery on sale 107.17$ Not Bad $
Original SMY SDNA 200 200W TC Box Mod

 

[mikepetro]

Better screen shot showing LED settings, from the Early Adopter site.

 

[TruckerMSA]

To me an LED fire button is kind of like a 180 degree forward looking camera in a car or truck. If you've got to look at a display on the dashboard to see what's in front of you, maybe you shouldn't be behind the wheel.

You mean like this [emoji12]lol its my dash cam so I can capture anybody who hits me in the front

 

[KTMRider]

I just got my Aromamizer v2. I built a simple single coil between the posts with Ni200 (.09Ω). I cleaned it with Dawn and hot tap water and it still has some machine oil taste to it. I'm usually a MTL'er and that's not really possible with this atomizer. It whistles a bit and not much better than my Lemo 2 for lung hits. I tried 2 air holes along the coil and by the post as well as all 4 holes open. I'm not that impressed with it.