Evolv-ing Thread

[mikepetro]

Interesting, I wonder how well that would do with a mod.

Jet Fusion Material for 3D Printing: 3D Printing Black Plastic

 

[SlickWilly]

This is the best "page not found" I've seen yet, cute.

http://lp.brownells.com/index.php/email/

Partial screen shot

 

[awsum140]

If NK popped a nuke way more than breakup of TV signals would happen. That would be the least of our problems. I haven't had the TV on since about 9, but it was solid then so it may be your provider.

 

[mikepetro]

If NK popped a nuke way more than breakup of TV signals would happen. That would be the least of our problems. I haven't had the TV on since about 9, but it was solid then so it may be your provider.

For one thing, there would be a new crater in the Koreas, possibly both of them.

 

[mikepetro]

 

[laurie9300]

I have gotten ? on some mods, from what I understand that means damn near 0 ohms which is good. You can check this by going under the mod tab, then down to mod Resistance, enter .05 ohms, also make sure under that, where it says Ohm Lock Range, that it's not blank, 0 or too low, the default is 25%, then upload the settings to the mod then recheck and see what you get, if it really was near zero with the ? it now should read near .05 ohms you entered, It may read minus - .05, can't remember if it will or not. If that checks out try another atty because from what you told me sounds like it's checking out OK, but some of the other guys know this stuff more in depth then I do and I'm sure then chime in later in the morning/day. Oh yeah, if those things don't work I guess you could try a hard reset, wouldn't hurt. But I'd do one thing/change at a time and recheck, if you do them all at once and it fixes it you won't know what the one cause was.

View attachment 688589

OK, no joy initially.....but....

I realised I hadn't set mod resistance to 0 before doing the test. So I set it to 0 and mod resistance came in at 0.003, which is lower than the original 0.004 it was set to initially. So the "?" must mean resistance is reading lower than mod resistance. I re-set mod resistance to 0.003......but it didn't help.

I checked my connections, factory reset, updated to SP26, nothing helped......

Swapped the board and it's all good! I got my 75C vape!

I see an RMA in my future, after I work out if it's worth the postage......

 

[laurie9300]

Sorry to hear that
Nothing more disappointing than having an issue with a new build
Only thing I can say is Grounding to the case cause's me a lot of head aches.
Try running a ground from the board to the - on the 510?

Thanks Steamer, but I'm not using the case as a ground.......

 

[dwcraig1]

Before work tonight I pulled an atty from the pile that I hadn't used for quite some time. Washed it out, dry burned, wicked.
All was good till half way to work when it went straight to TP. Checked resistance and it had doubled. First time this happened since the dual coil cartos.

 

[tiburonfirst]

 

[dwcraig1]

 

[Steamer861]

 

[Steamer861]

Swapped the board and it's all good! I got my 75C vape!

I see an RMA in my future, after I work out if it's worth the postage......

Alls well that ends well
I'm sure Evolv will come good of the defective board

 

[mikepetro]

 

[dwcraig1]

I got some kind of $10 worth store credit from Unkamen yesterday that was only good for 48 hours. Bought another 200 ft of 28 gauge ss430 for shipping charge of $3.65, probably never use what I have, but ya never know.
Edit: Meant to say $12, spent 10

 

[mikepetro]

Stolen from another thread!

 

[classwife]

 

[awsum140]

But I know where the pizza lives, Pizza Hut (yuck). And I thought tacos lived at Taco Bell (run for the ....).

 

[classwife]

We had a DiGiorno thin crust pepperoni pizza for dinner.
I want tacos now !

 

[mikepetro]

Me too, been eating FAR too much rabbit food lately!

 

[classwife]

Me too, been eating FAR too much rabbit food lately!

I need exercise...not rabbit food !!