Fasttech Veterans
- Thread starter trouble1000
- Start date
- th_trl_thread_readers 0
- Status
2.5 24 Awg 10 wrap !
EDit: As i said George it fires fine till i put it all together, gonna have to log off for a while, but i`ll be back on later
EDit: As i said George it fires fine till i put it all together, gonna have to log off for a while, but i`ll be back on later
There's not much room in there Terry.
I used 26 awg,2.5 and it has to be tight to the posts,just so you can barely see a gap.Is it possibly touching the chimney?
It has to be touching something George Yes. ( Short ) It`s getting a bit dark now, but i think i will just try to have another Look, i`ll post back in a bit mate.
Is this the tank? $9.21 Pico Styled RTA Rebuildable Tank Atomizer - 3ml / stainless steel + PEI / 22mm dia. at FastTech - Worldwide Free Shipping
I can only see 1.0ohm and 0.5 in the CLR coils, but they're $8.55 - am I looking at the wrong ones? FastTech - Gadgets and Electronics
George, you were right ! The coil was the culprit 
Ripped it out and replaced it with the pre-made, didn`t bother wicking it as it got dark, but i put it together again, and it`s firing 24 gauge must just be too thick, so i`ll use 26 if i`ve got any left that is.
So i will make another coil tomorrow, and have a proper blast with it. I`ve also got your tank all packed and ready to be posted tomorrow.
Ripped it out and replaced it with the pre-made, didn`t bother wicking it as it got dark, but i put it together again, and it`s firing 24 gauge must just be too thick, so i`ll use 26 if i`ve got any left that is. So i will make another coil tomorrow, and have a proper blast with it. I`ve also got your tank all packed and ready to be posted tomorrow.
Cut your cotton on the diagonal Terry,same length as the outside of base ring and taper it down the juice channels.
Not too long,just past the first step you can see in the channel.
Last edited:
Okay George will do, i`ve seen it done a couple of times on the boring reviews
They do look like they give a damn good vape though
They do look like they give a damn good vape though
They are a good vape Terry.Just a little tight for me.
It's funny how it's changed,i used to vape a mini naut on the smallest hole.The manufacturers only seem to want to build airy tanks now and you get used to them.
Whoever lung hit a cigarette
They are a good vape Terry.Just a little tight for me.
It's funny how it's changed,i used to vape a mini naut on the smallest hole.The manufacturers only seem to want to build airy tanks now and you get used to them.
Whoever lung hit a cigarette
I would imagine that would be a bit tricky to do George My mini fogger is a tightish draw as well, but the way i vape it suits me fine. I sort of fill me gob, then continue on to DTL for a split second !!
Made up some 10ml sample juices. Some with 5% and 10% purified water, and some with 5% and 10% vodka.
What on earth are you and Bob on about George
It's to make screens for the profiles on a dna200 Terry.
You have 8 different profiles you can load the csv's into(temp curves)for different types of wire.
And instead of just having them numbered 1-8 and having to remember what's in each number.
You just make a screen that says NI200,Nife30,SS 316L etc.
You have 8 different profiles you can load the csv's into(temp curves)for different types of wire.
And instead of just having them numbered 1-8 and having to remember what's in each number.
You just make a screen that says NI200,Nife30,SS 316L etc.
I went through all my fonts, looking for it, and must have missed Good Times (I was looking for the M as it is a different shape to normal fonts, Trebuchet was another that was almost the same, but the P was always different), oh well at least we know now, I use Lucida Handwriting in bold capitals on all mine for the wire profiles and the second welcome screen (except the VB-ERM where I have put my "HELLO BOB" on the first welcome screen)
Jon said it's the font Evolve use on their website.
It's not listed on paint but there are free downloads.
- Status
Similar threads
