Focalecig ... A new Fasttech??

[freedomfighter]

That's nice one. In 350 mod it's cute, very small, doesn't hit that that hard but pretty good. You will like it i'm sure.

My lock ring got stock so i just put it on side, as far i have alot of other toys. When i miss it i will deal with it))) First rule - do not go all man on it!!! *Nikkita*

The problem is this is my first time using rba with Stainless Steel Mesh haha.. anyone have tutorial for changing that mesh ? what size do i must use it? thanks

 

[Laylel]

The problem is this is my first time using rba with Stainless Steel Mesh haha.. anyone have tutorial for changing that mesh ? what size do i must use it? thanks

ooo this one to Nikki, i did give up on getting it right in time what i have for building coils, so i build with cotton.

 

[MTM]

I've never tried a mesh build. I know there are people here with knowledge of it though.

I have that same Kamry and same color! It was my first mechanical. I got it from the group buy.
I sanded the +&- battery contact points to expose better conductivity on it.
I have a chi-you clone kick tube that fits on the Kamry for use with a kick.
I originally got the kick tube to work with a Stainless Astro mod that I have but it fits Kamry. (my Vamo tubes actually fit it too)
The locking ring can be funky sometimes but it always gets unstuck pretty easily. Don't even have to go all man on it

 

[Corpse]

The problem is this is my first time using RBA with Stainless Steel Mesh haha.. anyone have tutorial for changing that mesh ? what size do i must use it? thanks

Check this
http://youtu.be/uX_hyJwQs_E
BUT when checking for hot spots don't touch the wire while firing it. It will short and break.

 

[freedomfighter]

Check this
The Chobra Set-up and First Impressions - YouTube
BUT when checking for hot spots don't touch the wire while firing it. It will short and break.

Thanks this will helpful, what size this cobra mesh anyway?

 

[Laylel]

Don't even have to go all man on it

It's from past he-he, i did ask my hubby to help with stack cartomizer... he went harsh on it and turned it into a oval, but still unscrewed, aha))) So now i avoid "all man" method

 

[Corpse]

Thanks this will helpful, what size this cobra mesh anyway?

In the video he uses a 35mm x 30mm piece of 400 mesh.

 

[Laylel]

My copper Nemmy landed in Canada, send on may 5, just landed + up too 7 days here... Gosh, it takes forever, can't wait.

 

[freedomfighter]

My copper Nemmy landed in Canada, send on may 5, just landed + up too 7 days here... Gosh, it takes forever, can't wait.

I am with you , i know that feeling . I went to usps when i saw my stuff already
at 4 or 5 block from my house here in chicago,

 

[Nikkita6]

Hello Nikkita6, can you please recommend a good charger for 18350 to 26650 for me?
I only have a questionable trustfire TR-001.
Thank you

Hello my friend, how are you? The nitecore i2 or i4 Intellichargers are awesome, I love mine. It detects the best charge setting for the battery type placed in it, and it automatically stops charging when done. And is also has reverse polarity protection, so I highly recommend it.

You can get one stateside for $20-$30 bucks, or from China for $15-20 ... I hear the Xtar chargers are good as well, but I feel really safe with the intelligcharger.

 

[Nikkita6]

That's nice one. In 350 mod it's cute, very small, doesn't hit that that hard but pretty good. You will like it i'm sure.

My lock ring got stock so i just put it on side, as far i have alot of other toys. When i miss it i will deal with it))) First rule - do not go all man on it!!! *Nikkita*

... Oh God, I still remember what happened to the poor Marstech tank

 

[Nikkita6]

The problem is this is my first time using RBA with Stainless Steel Mesh haha.. anyone have tutorial for changing that mesh ? what size do i must use it? thanks

There are plenty of building tutorials on youtube for Genesis style and working with ss mesh. I need to give you a "pow pow" freedomfighter, you could have been watching tutorials while you were waiting for your Cobra to show up

Go to youtube and search "Cobra rebuildable atomizer" and you should find what you need. After watching a few videos and understanding the basics, I can answer any further questions you might have about working with ss mesh.

 

[Nikkita6]

I've never tried a mesh build. I know there are people here with knowledge of it though.

I have that same Kamry and same color! It was my first mechanical. I got it from the group buy.
I sanded the +&- battery contact points to expose better conductivity on it.
I have a chi-you clone kick tube that fits on the Kamry for use with a kick.
I originally got the kick tube to work with a Stainless Astro mod that I have but it fits Kamry. (my Vamo tubes actually fit it too)
The locking ring can be funky sometimes but it always gets unstuck pretty easily. Don't even have to go all man on it

On of my favorite discoveries with my Astro mod was that I could use the kick ring on my SS Vamo V2 to create a 18500 battery configuration. *happy accident*

 

[Nikkita6]

It's from past he-he, i did ask my hubby to help with stack cartomizer... he went harsh on it and turned it into a oval, but still unscrewed, aha))) So now i avoid "all man" method

I die! ... "all man" method, and this is how we shall appropriately refer to it from now on!

 

[ScandaLeX]

I love my Kamry. Mine is set up with the dripper pro for trying new juices & it looks simply stellar.
I kind of miss using it. Sent it off to OCD Mods cause 101vape's *white* is dull gray.

Sent from a BIG phone.....Galaxy Note 3

 

[G-weezy]

Well I pulled the trigger on that RaiVapes Orochi. I'm intrigued by the snake design.

After watching the above video I went ahead and tried the Kraken again. I found out using SS mesh from a different place than the one that came with it was much easier to roll. I used a 2x2 inch piece and rolled it on a paperclip. Just kept on rolling till it was thin enough to fit. Actually worked. Lol.

On to the Cartel. I've been on parallel coil on this one. But......I had to try a low sub ohm. Dual parallel coil wrapped 4 times on a small screwdriver. Adjusted the coils to the middle on both. Woo wee. Had both air holes to the max. Tasted everything that juiced threw at me.

 

[haku]

Hello Nikkita6, can you please recommend a good charger for 18350 to 26650 for me?
I only have a questionable trustfire TR-001.
Thank you

i made some research for it recently, and the best option imo was the Thrunite MCC-4 (or 2) intellicharger. it also can charge Ni-MH batteries. makes different type of charge depending of battery type. it changes the step of the charge to take care of your Li-On batts (slowing down at the end, not overcharging them) but also with Ni-MH style. got one, and i'm very happy with it.
i've heard that Xtar chargers charge Li-On a bit better than this (but only a bit), but they don't use to charge Ni-MH, and are very expensive.

 

[Nikkita6]

Well I pulled the trigger on that RaiVapes Orochi. I'm intrigued by the snake design.

After watching the above video I went ahead and tried the Kraken again. I found out using SS mesh from a different place than the one that came with it was much easier to roll. I used a 2x2 inch piece and rolled it on a paperclip. Just kept on rolling till it was thin enough to fit. Actually worked. Lol.

On to the Cartel. I've been on parallel coil on this one. But......I had to try a low sub ohm. Dual parallel coil wrapped 4 times on a small screwdriver. Adjusted the coils to the middle on both. Woo wee. Had both air holes to the max. Tasted everything that juiced threw at me.

I am very intrigued by the Orochi mod, and I like the switch design, at least in concept. Dying to know if the switch is as nice as it should be based on design. I saw of pic of the Orochi with a brushed brass Kraken and it was sooo sexy! Can't wait to hear how this one turns out weezy.

I need to show my Kraken some love, it has been neglected for months now ... still have my last dual coil mesh build in it, but the juice I left in the tank? ... yikes

My Cartel/Stillare definitely puts out the clouds ... dual coil 1.4 ohm build, air hole less than half open = serious clouds .. like the kind that linger for a long time, so I can only imagine what its putting out with sub build. #MAJORVAPOR

 

[Nikkita6]

i made some research for it recently, and the best option imo was the Thrunite MCC-4 (or 2) intellicharger. it also can charge Ni-MH batteries. makes different type of charge depending of battery type. it changes the step of the charge to take care of your Li-On batts (slowing down at the end, not overcharging them) but also with Ni-MH style. got one, and i'm very happy with it.
i've heard that Xtar chargers charge Li-On a bit better than this (but only a bit), but they don't use to charge Ni-MH, and are very expensive.

That charger sounds good, but I am not familiar with it ... Nitecore Intellichargers also charge Ni-MH batteries which I use for my camera. It also charges Ni-Cd rechargeable batteries, and it detects appropriate charges modes for each battery type (Constant charge current, constant charge voltage, and trickle charge). The battery slots work independently.

Nitecore Intellicharger is compatible with Li-ion size 26650,22650, 18 series, 17 series, 14500 and RCR123 ... Ni-MH & Ni-Cd AA AAA and C battery sizes.

 

[G-weezy]

Nitecore i4 charger is very nice. Accommodates all sorts and sizes of the batteries I have. I got a good deal on eBay for it.